TransTalk™ 9000
`Digital Wireless System
`MDW 9030P Wireless Pocketphone
`Installation and Use
`
`503-801-160
`Comcode 107972010
`Issue 2
`March 1997
`
`Juniper Ex 1035-p. 1
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Copyright ©1997 Lucent Technologies
`All Rights Reserved
`Printed in U.S.A.
`
`Lucent Technologies 503-801-160
`Comcode 107972010
`Issue 2
`March 1997
`
`Notice
`Every effort was made to ensure that the information in this book was complete and
`accurate at the time of printing. However, information is subject to change. The pictures in
`this book are for illustrative purposes only; your actual hardware may look slightly different.
`
`Federal Communications Commission (FCC) and Industry Canada (IC) Information
`For details, see Appendix B.
`
`Security
`Toll fraud, the unauthorized use of your telecommunications system by an unauthorized
`party (for example, persons other than your company’s employees, agents, subcontrac-
`tors, or persons working on your company’s behalf) can result in substantial additional
`charges for your telecommunications services. You are responsible for the security of your
`system. There may be a risk of toll fraud associated with your telecommunications system.
`You are responsible for programming and configuring your equipment to prevent unautho-
`rized use. Your system administrator should read all documents provided with this product
`to fully understand the features that can introduce the risk of toll fraud and the steps that
`can be taken to reduce that risk. Lucent Technologies does not warrant that this product is
`immune from or will prevent unauthorized use of common-carrier telecommunication
`services or facilities accessed through or connected to it. Lucent Technologies will not be
`responsible for any charges that result from such unauthorized use.
`
`Trademarks
`TransTalk is a trademark of Lucent Technologies and DEFINITY, MERLIN, MERLIN LEG-
`END, PARTNER, and SYSTIMAX are registered trademarks of Lucent Technologies. Supra
`is a registered trademark of Plantronics, Inc.
`
`Warranty
`Lucent Technologies provides a limited warranty for this product; see Appendix A.
`
`Ordering Information
`The order number for this book is 503-801-160. The order number for the MDW 9030P
`Wireless Pocketphone Quick Reference is 503-801-161. To order additional copies of
`these reference materials, call 1 800 457-1235 or 1 317 361-5353. To order parts and
`accessories, see “Ordering Replacement & Optional Parts” in Chapter 4.
`
`Customer Support
`In the continental U.S., call 1 800 628-2888 if you need assistance when using your
`wireless phone with a PARTNER, MERLIN, or MERLIN LEGEND system. Consultation
`charges may apply. For all other systems, follow the procedure you normally use to get
`support for your communications system.
`
`Outside the continental U.S., contact your Lucent Technologies Representative or local
`Authorized Dealer.
`
`Juniper Ex 1035-p. 2
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Using the MDW 9030P Pocketphone 3
`
`Important Safety Instructions
`
`Please see "Important Safety Instructions" at the beginning of Chapter 2.
`
`The Handset
`
`This section describes the handset and how to use it. It also explains how to use a head-
`set.
`
`Using the MDW 9030P Pocketphone 3-1
`
`Juniper Ex 1035-p. 3
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Receiver
`Receives the sound of your
`caller's voice, unless a
`headset is connected.
`
`Antenna
`Extend fully or retract fully to
`use handset. Extend fully to
`maximize the handset range
`and voice quality.
`
`Handset Display
`Displays status of lines and
`range. For a detailed
`description, see “Handset
`Display” later in this
`chapter.
`Column
`Use together with Select
`button to choose a line or
`programmable/intercom/
`drop button.
`
`Redial
`Press to dial again the last
`number manually dialed
`from the handset.
`Select
`Use to move the Selection
`rectangle, and, together
`with Column buttons, to
`choose a line or program-
`mable/intercom/drop
`button. Also use to wake-
`up the phone.
`
`Mute
`Press to turn the micro-
`phone off for privacy .
`
`Headset Connector
`Plug in the headset cord to
`use the headset.
`
`212 555 1212
`MSG
`ON
`
`7
`
`3
`
`C
`
`8
`
`4
`
`D
`
`6
`
`B2
`
`5
`
`1
`
`A
`
`On/Off
`
`Redial
`
`Mute
`
`Feat/P
`
`Conf
`
`1
`
`4
`
`GHI
`
`2
`
`5
`
`ABC
`
`JKL
`
`3 DEF
`
`MNO6
`
`Trans
`
`7
`PQRS
`
`TUV8
`
`9
`
`WXYZ
`
`Hold
`
`0
`
`OPER
`
`TransTalk
`
`Handset Controls
`
`Headset On/Off
`Press to turn the headset on if the
`headset is plugged in. ON
`appears in handset display. To
`turn off, press again. Turn on to
`make or answer a call, and turn off
`to “hang up.”
`
`Lanyard Loop
`Attach lanyard for carrying
`handset.
`
`Volume Control
`Press "+" to increase or "-" to
`decrease volume of receiver or
`alerter.
`
`On/Off
`Press to turn the handset on. ON
`appears in handset display. To
`turn off, press again. Turn on to
`make or answer a call, and turn
`off to “hang up.”
`
`Feat/P (Feature/Program)
`Press to use dial-code features
`(PARTNER systems only) or to
`enter programming mode.
`
`Conf (Conference)
`Press to conference in (add)
`another party to your call.
`
`Trans (Transfer)
`Press to transfer a call to
`another extension.
`
`Hold
`Press to put a call on hold.
`
`3-2 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 4
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Column and Select Buttons
`
`The MDW 9030P Pocketphone can display the status of up to 12 lines or programmable/
`intercom/drop buttons; however, it has only 4 selection buttons (the Column buttons). The
`Select button (") is used in conjunction with the Column buttons (’) to increase the
`available selections to 12. Each Column button (’) affects one of the three lines or
`programmable/intercom/drop buttons directly above it, as shown in the illustration below.
`
`ON
`
`Each time you press the Select button ("), the Selection rectangle moves to another row
`(cycling through the three rows in turn). The Column buttons (’) each represent one of
`the four lines or programmable/intercom/drop buttons in the row enclosed by the Selec-
`tion rectangle.
`
`Selection rectangle
`
`ON
`
`For example, suppose your handset shows the Selection rectangle around the middle row
`of lines. If you press the second Column button from the left (shaded in the illustration
`above), you select Line 2, as indicated by the truncated triangle in the illustration.
`
`Note:
`If you have a communications system other than PARTNER, the line you select is
`indicated by a small rectangle instead of the triangle, as shown below:
`
`ON
`
`See "Manually Selecting a Line or Programmed Button" and "Preselecting a Line" later in
`this chapter for more information about the Column and Select buttons.
`
`Using the MDW 9030P Pocketphone 3-3
`
`Juniper Ex 1035-p. 5
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Handset Display
`
`The MDW 9030P Pocketphone display has one 16-alphanumeric-character line, and four
`lines of icons to provide you with status information.
`
`7
`
`9
`
`3
`
`4
`
`5
`
`6
`
`MSG
`
`RANGE
`
`ON
`
`MUTE
`
`8
`
`1 2
`
`Note:
`This illustration is intended to show you what all of the indicators look like, but you will
`never see all of the line status indicators illuminated at once.
`
`1 This line of the display gives you the information you would see on a wired system
`phone's display, except that the time is not provided. The information varies accord-
`ing to which communications system you are using. For example, the display may
`show the current date, the number you are calling, or caller ID information (if the
`system supports this feature). This display line is also used for feedback when testing
`and programming the handset. See "Display Messages" later in this chapter for more
`information about messages.
`2 MSG icon indicates that you have a message.
`3 RANGE icon indicates that the handset is out of range or almost out of range. The
`handset also beeps. For more information, see “Range Indicators” later in this chap-
`ter.
`4 ON icon indicates that the handset has been turned on by pressing O.
`5 Battery icon flashes to indicate a low battery condition. The handset also emits 2
`beeps. For more information, see “Low Battery Indicator” later in this chapter.
`6 No Ring icon indicates that the alerter is disabled. If the alerter is enabled, no icon
`is displayed.
`7 MUTE icon indicates that the handset microphone was turned off by pressing M.
`8 Line Status Indicators show the status of line or programmable/intercom/drop
`buttons. See Chapter 6 for button-mapping information. Also see "Line Status
`Indicators" later in this chapter.
`9 Selection rectangle indicates the active row for line or programmable/intercom/drop
`button selection. See "Column and Select Buttons" earlier in this chapter.
`When the display is blank, the handset is either turned off or in the power-saving "sleep"
`mode. You can activate the display by pressing O to turn the handset on or by
`pressing " to "wake it up."
`
`3-4 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 6
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Display Messages
`The top line of the handset display uses up to 16 alphanumeric characters to provide
`messages such as the following:
`
`n LCL:P (or LCL:D, LCL:M1, or LCL:M2) indicates that the handset is in Local Mode,
`and tells which communications system the button mapping is set to emulate:
`
`LCL:P
`LCL:D
`LCL:M1
`
`PARTNER systems
`DEFINITY systems, System 25, System 75, and System 85
`All MERLIN systems (except MERLIN 410 and MERLIN 820),
`including MERLIN LEGEND
`MERLIN 410 and MERLIN 820
`LCL:M2
`n WIRELESS TEST indicates that the handset is in Wireless Test Mode; 1 through 10
`are used to measure signal strength and voice quality in Wireless Test Mode.
`
`n VIBR indicates that the vibrator is enabled to notify you of incoming calls.
`
`n PSEL indicates that Line Preselection is enabled.
`
`n PRESELECTION:ON or PRESELECTION:OFF is displayed when you enter Preselec-
`tion Mode, and indicates the status of the Line Preselection option.
`
`n CHANGE BUTTN MAP is an error message indicating that the handset is set for the
`wrong communications system. See "Changing the Communications System Setting"
`in Chapter 2 for instructions for changing the setting.
`
`n MAP:P (or MAP:D, MAP:M1, or MAP:M2) is displayed when you enter Button Map-
`ping Mode, and indicates the communications system to which the MDW 9030P
`buttons are currently mapped:
`
`MAP:P
`MAP:D
`MAP:M1
`
`PARTNER systems
`DEFINITY systems, System 25, System 75, and System 85
`All MERLIN systems (except MERLIN 410 and MERLIN 820),
`including MERLIN LEGEND
`MERLIN 410 and MERLIN 820
`MAP:M2
`n NO LINK is an error message indicating that the handset is not communicating with its
`radio module. See Chapter 5, "Troubleshooting," for help in resolving this problem.
`
`Line Status Indicators
`There are 12 status indicators; each one corresponds to a specific outside line or pro-
`grammable/intercom/drop button. (The function of these status indicators varies, depend-
`ing on the communications system you are using—see button mapping for the appropri-
`ate communications system switch in Chapter 6, "MDW 9030P Pocketphone Compatibil-
`ity.") The status indicators show either a truncated triangle or a rectangle, signifying
`activity as follows:
`
`PARTNER Systems:
`A rectangle (
` ) is the equivalent of a red LED on a wired system phone.
`A truncated triangle (
`) is the equivalent of a green LED on a wired system phone.
`
`All Other Systems:
`A rectangle (
` ) is the equivalent of a green LED on a wired system phone.
`A truncated triangle (
`) is the equivalent of a red LED on a wired system phone.
`
`Using the MDW 9030P Pocketphone 3-5
`
`Juniper Ex 1035-p. 7
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Range Indicators
`
`For maximum range and voice quality, always fully extend the antenna before placing or
`answering a call. The antenna must be either fully retracted (for short range) or fully
`extended (for maximum range) to use the Pocketphone.
`
`The handset provides an audible and a visual signal to alert you when the handset is near
`the end of the range of the radio module. Depending on how far away the handset is from
`the radio module, the signals function as follows:
`
`n The handset emits two beeps and flashes the RANGE indicator continuously.
`
`Out of optimal range. You have walked into an area that is near the end of the operat-
`ing range of the radio module. You can continue your conversation or initiate a call,
`but you are likely to experience a degradation in voice quality.
`
`n The handset emits five sets of beeps and displays the RANGE indicator.
`
`Loss of communication link. You have walked into an area that is out of the operat-
`ing range of the radio module. You must bring the handset within range of the radio
`module within several seconds or the handset will turn off. If the handset turns off, it
`appears that your call was disconnected; however it was only placed on Hold. To talk
`with your party, move back towards the radio module, press O, then proceed as
`you would for any call placed on Hold.
`
`n When you try to make a call, the handset emits two beeps and flashes the RANGE
`indicator twice; then the handset automatically turns off.
`
`Cannot establish communication link. You are completely out of range of the radio
`module. To make the call, move back towards the radio module and try again.
`
`Refer to Chapter 5, “Troubleshooting,” for additional information about out-of-range
`conditions.
`
`Low Battery Indicator
`
`When the handset is On and the battery power is low, the handset will emit two beeps and
`the Battery icon in the handset display will flash. When this occurs, you have 5 minutes or
`less of talk time left. At this point, you can either:
`
`n Complete your call, turn the handset off, and recharge the battery pack, or
`
`n
`
`If you have a charged spare battery pack, place your call on Hold and replace the
`handset battery pack with the spare battery pack. Wait 6 to 10 seconds, then turn the
`handset on and proceed as you would for any call placed on Hold.
`
`NOTE:
`When the battery power is low, the two beeps will sound each time either O button
`is pressed until either the battery is drained or you replace the battery. If you continue
`talking, the handset will turn off when the battery pack is drained. Your call will be
`placed on Hold automatically so that you can swap battery packs or pick up the call
`on another telephone.
`
`3-6 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 8
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Volume Control
`
`To increase or decrease the volume of the handset alerter or the receiver (earpiece):
`
`n Alerter: Press the “+” or the “–” button while the MDW 9030P is awake but turned off.
`If the display is dark (the phone is in "sleep" mode), press " to wake it up, then press
`the “+” or the “–” button.
`
`n Receiver: Press the “+” or the “–” button while the MDW 9030P is turned on.
`
`+
`
`–
`
`+ and – Volume Control Buttons
`
`Lanyard Loop
`
`Carrying Your Pocketphone
`
`The MDW 9030P Pocketphone has a loop in the upper corner to accommodate the
`included lanyard. You can attach the lanyard, as illustrated above, and slip the lanyard
`over your wrist to guard against dropping the phone. A leather carrying case is also
`available separately (see "Ordering Replacement & Optional Parts" in Chapter 4).
`
`The MDW 9030P Pocketphone also comes with a detachable clip, which you can attach
`to the back of the battery pack, that enables you to attach the phone to your belt or purse
`strap. To attach the clip to the battery pack, do the following:
`
`Remove the battery pack from the
`1
`handset, as described in "Inserting and
`Removing the Handset's Battery Pack" in
`Chapter 2.
`
`Place the two metal tabs on the clip into
`2
`the slots on the battery pack, with the
`"hooks" toward the bottom of the battery pack.
`
`3
`
`Slide the clip toward the bottom of the
`battery pack to engage the hooks.
`
`Reinsert the battery pack in the handset,
`4
`as described in "Inserting and Removing
`the Handset's Battery Pack" in Chapter 2.
`
`Using the MDW 9030P Pocketphone 3-7
`
`Juniper Ex 1035-p. 9
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Antenna
`
`The MDW 9030P Pocketphone comes with a user-replaceable, flexible, retractable
`antenna. For maximum range and voice quality, always fully extend the antenna before
`placing or answering a call. You can receive a call (if you are within range of the radio
`module) without extending the antenna, but you may get a RANGE indication. The
`antenna must be fully extended for optimal performance.
`
`Changing the Handset Settings
`
`You can use Local Mode to change the handset settings for these functions:
`
`n Communications system button mapping
`
`n Vibrator
`
`n Line Preselection
`
`n Alerter
`
`Local Mode also gives you access to Local Test Mode (which enables you to test the
`alerter, vibrator, and display) and Wireless Test Mode (which enables you to test sound
`clarity, signal strength, and voice quality). While in Local Mode, the MDW 9030P can still
`receive notification of incoming calls.
`
`To access Local Mode, use the following procedure:
`
`1. Make sure the handset is turned off.
`
`2. Press and hold the Select button (") for three seconds.
`
`3. While still holding ", press O.
`
`The handset beeps twice, and the display shows the handset settings. For example,
`the following display indicates that the handset:
`
`n
`
`Is using button mapping for a PARTNER switch
`
`n Has the vibrator and Line Preselection enabled
`
`n Has the alerter disabled
`
`To exit Local Mode, press O.
`
`Changing the Communications System Button Mapping Setting
`If the MDW 9030P Pocketphone is set to use the wrong communications system, an error
`message saying CHANGE BUTTN MAP shows on the top line of the handset display
`each time the O button is pressed. If you see this message, use the procedure
`described in "Changing the Communications System Setting" in Chapter 2 to specify the
`correct communications system setting.
`
`3-8 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 10
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Enabling or Disabling the Vibrator
`The vibrator vibrates to alert you to an incoming call in situations where you do not want to
`disturb others with an audible ring. You can enable or disable the vibrator using the
`following procedure:
`
`1. Make sure the handset is turned off.
`
`2. Press and hold the Select button (") for three seconds.
`
`3. While still holding ", press O.
`
`The handset beeps twice, and the display shows the handset settings, indicating that
`you are now in Local Mode. (While in Local Mode, the MDW 9030P can still receive
`notification of incoming calls.)
`
`If the vibrator is enabled, the VIBR icon appears in the display. For example:
`
`ON
`
`If the vibrator is disabled, no icon appears.
`
`4. Press "V" (8) on the dialpad to enable or disable the vibrator.
`
`5. Press O to exit Local Mode.
`
`Note:
`Both the alerter and the vibrator can be disabled at the same time. In this case the
`only notification you have of an incoming call is that a line status indicator (a truncated
`triangle or a rectangle, depending on your communications system) flashes in the
`display.
`
`Enabling or Disabling Line Preselection
`Line Preselection lets you choose the line or button you want to use before turning the
`handset on. For example, suppose your phone is ringing but you want to pick up a call
`that is holding on another line instead of the ringing call. In normal operation, the commu-
`nications system automatically connects you to the ringing line as soon as you turn on the
`handset. With Line Preselection enabled, you can select the line you want to connect to
`before turning on the handset.
`
`Note:
`Under certain conditions, the communications system tries to turn on a speaker; for
`example, if you use Line Preselection to select a button programmed for speed-
`dialing. Since the MDW 9030P Pocketphone has no speaker, the system causes the
`ON icon in the handset display to flutter. You must press O to complete the
`connection.
`
`Note:
`When Line Preselection is enabled, you do not have to use it; however you cannot use
`it unless it is enabled.
`
`Using the MDW 9030P Pocketphone 3-9
`
`Juniper Ex 1035-p. 11
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`To enable Line Preselection, use the following procedure:
`
`1. Make sure the handset is turned off.
`
`2. Press and hold the Select button (") for three seconds.
`
`3. While still holding ", press O.
`
`The handset beeps twice, and the display shows the handset settings, indicating you
`are in Local Mode. (While in Local Mode, the MDW 9030P can still receive notification
`of incoming calls.)
`
`If Line Preselection is enabled, PSEL shows on the top line of the display. For ex-
`ample:
`
`If Line Preselection is disabled, no icon appears.
`
`4. Press and hold "P" (7) for three seconds.
`
`The handset display shows PRESELECTION:ON if Line Preselection is enabled or
`PRESELECTION:OFF if Line Preselection is disabled. For example:
`
`5. Press " to toggle between ON and OFF to enable or disable Line Preselection.
`
`6. Press O to exit Local Mode.
`
`3-10 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 12
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Enabling or Disabling the Alerter
`
`The alerter is an audible signal to notify you of an incoming call. If a call comes in while
`the phone is idle, the handset rings. If you are already on a call, the handset chirps softly.
`You can adjust the volume of the alerter by pressing the "+" button or the "–" button on the
`side of the handset when the phone is turned off. You can enable or disable the alerter
`using the following procedure:
`
`1. Make sure the handset is turned off.
`
`2. Press and hold the Select button (") for three seconds.
`
`3. While still holding ", press O.
`
`The handset beeps twice, and the display shows the handset settings, indicating you
`are in Local Mode. (While in Local Mode, the MDW 9030P can still receive notification
`of incoming calls.)
`
`If the alerter is disabled, the No Ring icon (a bell with a line through it) appears in the
`second line of the display. For example:
`
`ON
`
`If the alerter is enabled, the icon is not displayed. For example:
`
`ON
`
`4. Press "A" (2) on the dialpad to enable or disable the alerter.
`
`5. Press O to exit Local Mode.
`
`Note:
`Both the alerter and the vibrator can be disabled at the same time. In this case the
`only notification you have of an incoming call is that a line status indicator (a truncated
`triangle or a rectangle, depending on your communications system) flashes in the
`display.
`
`Using the MDW 9030P Pocketphone 3-11
`
`Juniper Ex 1035-p. 13
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Test Modes
`
`You can use Local Test Mode and Wireless Test Mode to verify that your handset is
`working properly and that the MDW 9030P system is performing optimally.
`
`Using Local Test Mode
`
`You can use Local Test Mode to activate the audio warning signal, the vibrator, and all
`visual indicators on the handset display, enabling you to test the following:
`
`n Does the audio warning signal work?
`n Does the vibrator vibrate?
`Is the display operational?
`n Are the visuals bright and clear?
`
`n
`
`Note:
`While in Local Test Mode, the MDW 9030P cannot make or receive calls.
`
`1. Make sure the handset is turned off.
`
`2. Press and hold the Select button (") for three seconds.
`
`3. While still holding ", press O.
`
`The handset beeps twice, and the display shows the handset settings, indicating you
`are in Local Mode. (While in Local Mode, the MDW 9030P can still receive notification
`of incoming calls.)
`
`4. Press # to enter Local Test Mode.
`
`The handset emits two beeps, the vibrator vibrates, and all indicators on the display
`appear (including the rectangles and truncated triangles), as shown below.
`
`Local Test Mode
`
`MSG
`
`RANGE
`
`ON
`
`MUTE
`
`If the beeps do not sound, the vibrator does not vibrate, or the indicators do not
`appear, repeat Steps 1–4. If you still have problems, call for customer support as
`described on the inside front cover of this book.
`
`3. Press O once to exit both Local Test Mode and Local Mode.
`
`You must exit Local Test Mode to reinstate proper call handling.
`
`3-12 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 14
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Using Wireless Test Mode
`
`You can determine sound clarity, signal strength, and voice quality using Wireless Test Mode.
`You can also use Wireless Test Mode to identify which radio module matches your
`handset.
`
`NOTE:
`Ignore anything that displays if you press 4 or 5 while in Wireless Test Mode. These
`displays are for Lucent Technologies technicians’ use only.
`
`To identify the matching radio module for your handset, use the following procedure:
`
`1. Make sure the handset is turned off.
`
`2. Press and hold the Select button (") for three seconds.
`
`3. While still holding ", press O.
`
`The handset beeps twice, and the display shows the handset settings, indicating you
`are in Local Mode. (While in Local Mode, the MDW 9030P can still receive notification
`of incoming calls.)
`
`4. Press "W" (9) to enter Wireless Test Mode.
`
`WIRELESS TEST appears on the top line of the handset display. The handset beeps
`twice and vibrates, then you hear a simulated dial tone. This dial tone continues until
`you exit Wireless Test Mode. While in this mode, the MDW 9030P cannot make or
`receive calls.
`
`5. To identify the matching radio module for this handset, press 3.
`
`The display indicates in which slot in the individual carrier (SLOT:n) the matching
`radio module is located, using a number (n) from 1 to 6 . A stand-alone radio module
`is shown as 0. For example:
`
`ON
`
`6. To exit Wireless Test Mode and Local Mode, press O.
`
`Using the MDW 9030P Pocketphone 3-13
`
`Juniper Ex 1035-p. 15
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Performance/Range Test in Wireless Test Mode
`Using the signal-strength test and the voice-quality test together, you can determine the
`range in which your MDW 9030P Pocketphone performs best at your site:
`
`At 10–15 feet (3.1–4.6 m) from its radio module, use the following procedure:
`
`1. Make sure the handset is turned off.
`2. Press and hold the Select button (") for three seconds.
`3. While still holding ", press O.
`The handset beeps twice, and the display shows the handset settings, indicating you
`are in Local Mode. (While in Local Mode, the MDW 9030P can still receive notification
`of incoming calls.)
`4. Press "W" (9) to enter Wireless Test Mode.
`WIRELESS TEST appears on the top line of the handset display. The handset beeps
`twice and vibrates, then you hear a simulated dial tone. This dial tone continues until
`you exit Wireless Test Mode. While in this mode, the MDW 9030P cannot make or
`receive calls. For more information, see "Wireless Test Mode" in Chapter 2.
`5. Press 1.
`The display should show a 9 or 10 for signal strength. If it does not, see Chapter 5,
`"Troubleshooting," for help with range problems.
`6. Press 2.
`The display should show a 9 or 10 for voice quality. If it does not, see Chapter 5,
`"Troubleshooting," for help with range problems and/or voice quality problems.
`7. Periodically check the signal strength and voice quality as you walk away from the
`radio module. Each time you press 1 or 2, you get a new reading.
`When you see a signal strength of 3, you are at the "edge of range" for the MDW
`9030P Pocketphone. The distance will vary depending on the environment, building
`structure, and other factors. The range in an average office building is 500–700 feet
`(152.5–213.5 m). If, however, dense walls intervene, the distance could be less.
`8. With a signal strength of 3, press 2 to check the voice quality. When the voice
`quality is 7 or 8, the voice connection should be satisfactory. This is the edge of your
`usable range.
`The following diagram illustrates this Performance/Range test.
`
`Close-Up Test
`10 to 15 feet (3.1 to 4.6 m)(cid:13)
`Signal Strength = 9 to 10(cid:13)
`Voice Quality = 9 to 10
`
`Edge-of-Usable-Range Test
`Signal Strength = 3(cid:13)
`Voice Quality = 7 to 8
`
`POWER
`
`RADIO
`
`PASS
`
`Radio (cid:13)
`Module
`
`3-14 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 16
`Juniper v ChriMar
`IPR2016-01397
`
`

`

` "Waking Up" the Phone
`
`In addition to "On" and "Off," the MDW 9030P has an energy-saving "sleep" or "standby"
`mode. The MDW 9030P "goes to sleep" 15 seconds after activity ceases (that is, after an
`alert stops ringing or after you hang up).
`
`The O and " buttons "wake up" the phone. The headset and handset O
`buttons turn the phone on, and the Select button (") signals the phone that activity is
`occurring. You can activate the display to see whether you have a message or to check
`whether your alerter is enabled without actually turning the phone on (if the communica-
`tions system is very busy, for instance) by pressing ".
`
`Making a Call
`
`To make a call using your MDW 9030P, use the following procedure:
`
`1. Press the handset O button (or the headset O button if you have the headset
`attached) to turn the phone on.
`
`– The MDW 9030P seizes an available line and a truncated triangle or a small rect-
`angle (depending on your communications system) appears around that line in the
`handset display.
`– You hear a dial tone.
`
`2. Dial the call as you would on a wired system phone.
`
`3. To end the call, press the O button.
`
`After 15 seconds, unless there is other activity on the phone, the handset goes into the
`energy-saving "sleep" mode.
`
`Answering a Call
`
`When you receive a call on your MDW 9030P Pocketphone, you hear a ringing tone if your
`alerter is enabled, or you feel a vibration in the handset if the vibrator is enabled, or both.
`To answer the call, use the following procedure:
`
`1. Press the handset O button (or the headset O button if you have the headset
`attached) to turn the phone on.
`
`You are automatically connected to the ringing line.
`
`4. Speak into the handset to converse with your caller.
`
`5. To end the call, press the O button.
`
`After 15 seconds, unless there is other activity on the phone, the handset goes into the
`energy-saving "sleep" mode.
`
`Using the MDW 9030P Pocketphone 3-15
`
`Juniper Ex 1035-p. 17
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Manually Selecting a Line or Programmed Button
`
`When you are making or answering a call, the MDW 9030P automatically selects the line
`for you. In some situations, however, you may want to select a particular line (for ex-
`ample, to use an "800" line). To select a particular line or programmable/intercom/drop
`button, use the following procedure:
`
`1. Press O.
`
`The ON icon displays steadily, and you are connected to an available line.
`
`2.
`
`If the Selection rectangle in the handset display is not surrounding the row that in-
`cludes the line or button you want to use, press " one or more times until the rect-
`angle encloses that row. (See "Column and Select Buttons" earlier in this chapter for
`more information.)
`
`3. Press the ’ button that corresponds to the line or button within the Selection rect-
`angle that you want to select.
`
`You are connected to the line or you have access to the button you chose.
`
`To deselect the line or button, press O.
`
`For information about assigning features to buttons, see "Programming Features for
`PARTNER, MERLIN, and MERLIN LEGEND Systems" in Chapter 6.
`
`Preselecting a Line
`
`You may sometimes want to select a line other than the line to which the communications
`system automatically connects you. To preselect a line, you must first enable Line
`Preselection. See "Enabling or Disabling Line Preselection" earlier in this chapter.
`
`Once Line Preselection is enabled, use the following procedure:
`
`1.
`
`2.
`
`If the handset is "asleep," press " to wake it up and activate the display.
`
`If the Selection rectangle in the handset display is not surrounding the row that in-
`cludes the line you want to use, press " repeatedly until the rectangle encloses that
`row. (See "Column and Select Buttons" earlier in this chapter for more information.)
`
`3. Press the ’ button that corresponds to the line within the Selection rectangle that
`you want to select.
`
`The ON icon flashes in the display and the handset emits double beeps.
`
`4. Press O.
`
`The ON icon displays steadily, and you are connected to the line you chose.
`
`3-16 Using the MDW 9030P Pocketphone
`
`Juniper Ex 1035-p. 18
`Juniper v ChriMar
`IPR2016-01397
`
`

`

`Using a Headset
`
`Lucent Technologies offers the Supra 9030 headset, which is specifically designed for
`use with your MDW 9030P wireless phone. A headset assists in call answering, and
`provides hands-free operation.
`
`For ordering information, see "Ordering Replacement & Optional Parts" in Chapter 4.
`
`To use the Supra 9030 headset, hold its cord with the "UP" label facing you, and insert the
`plug directly into the headset connector on the bottom of the handset (near the mouth-
`piece).
`
`! CAUTION:
`Plug ONLY the Supra 9030 headset cord into the headset connector.
`
`NOTE:
`Calls cannot be heard on the handset receiver when the headset is plugged in to the
`headset connector. The handset microphone is also deactivated. The range of the
`handset is slightly diminished when you are using a headset. You may need to move
`closer to the radio module, or move the radio module closer to you.
`
`If d