`
`
`
`Description:
`Introducing the ADS-C232-1AD, Watson
`Industries newest sensor system! It is a much
`smaller, yet fully functional vertical reference
`system that can serve as a replacement for a
`Watson VRS in many applications.
`
`The Watson Industries Dual Axis Vertical
`Reference System is a solid-state gyro package
`that measures angular displacement and rate,
`especially where dynamic motion may
`interfere. Under these conditions, the effects
`of lateral accelerations severely limit the
`performance of an ordinary accelerometer or
`pendulous device.
`
`
`
`Dual Axis Vertical
`Reference System
`
`ADS-C232-1AD
`
`
`
`The Watson Dual Axis Vertical Reference achieves exceptional performance by integrating the output
`of a vibrating structure gyro to get an estimate of the attitude, which is then compared to accelerometers
`to find the error. The error is filtered over a long time constant and subtracted from the rate gyro output
`to correct biases in a closed loop error correction system. This process lets the gyro measure short-term
`attitude accuracy above the correction loop frequency while the accelerometer serves as the long-term
`reference.
`
`The ADS can be a functional replacement for mechanical gyros, which are often more expensive, larger,
`heavier and less reliable than this solid-state sensor. It is especially suited for applications where there is
`limited bank and elevation such as ships, underwater vehicles, some land vehicles, and certain camera
`applications.
`
`• Solid State, Strap Down System
`• High Accuracy
`• Low Cost, Low Power
`• Rugged, High Reliability
`• Analog and RS-232 Digital Outputs
`• One Year Limited Warranty
`• Engineering Support
`
`Applications:
`The ADS is used to stabilize and control
`ships and submersibles, to stabilize
`antenna platforms, to instrument
`automobiles, and for many other
`applications.
`
`Watson Industries, Inc.
`3035 Melby Street Eau Claire, Wisconsin 54703 U.S.A
`Phone: +1 (715) 839-0628
`Fax: +1 (715) 839-8248
`e-mail: support@watson-gyro.com Website: www.watson-gyro.com
`
`
`
`
`
`APPLE 1022
`
`1
`
`
`
`
`
`Attitude
`
`
`Digital (Analog)
`±180° (±30° †)
`
`Range: Bank
`Digital (Analog)
`±90° (±30° †)
`
`Range: Elevation
`Binary mode (14 bit)
`0.02°
`
`Resolution:
`±10V Output
`3°/V †
`
`Analog Scale Factor:
`(up to 75°)
`±0.5°
`
`Accuracy: Static
`
`0.5%
`* Accuracy: Dynamic
`Angular Rate
`
`
`
`±100°/sec
`
`Range: Roll, Pitch
`Binary mode (14 bit)
`0.025°/sec
`
`Resolution:
`±10V Output
`10°/sec/V
`
`Analog Scale Factor:
`
`0.5%
`
`Scale Factor Accuracy:
`±0.02°/sec Binary mode (14 bit)
`< 0.3°/sec
`
`Bias: Roll, Pitch
`Full scale range
`< 0.2%
`
`Non-Linearity:
`
`50 Hz
`
`Bandwidth:
`
`< 0.06°/sec rms
`
`Noise:
`Acceleration
`
`
`
`±10g
`
`Range: X, Y, Z
`
`4mg
`
`Resolution:
`
`1%
`
`Scale Factor Accuracy:
`
`< 10mg
`
`Bias:
`Full scale range
`0.5%
`
`Non-Linearity:
`
`3 Hz
`
`Bandwidth:
`Environmental
`
`
`
`-40°C to +85°C
`
`Temperature: Operating
`
`-55°C to +85°C
`
`Temperature: Storage
`20 Hz to 2 KHz
`5g rms
`
`Vibration: Operating
`20 Hz to 2 KHz
`10g rms
`
`Vibration: Survival
`1mS ½ sine wave
`500g
`
`Shock: Survival
`Electrical
`
`
`Maximum
`250 Hz
`
`Frame Rate:
`
`5 sec
`
`Startup Time: Data
`
`10 sec
`
`Startup Time: Fully operational
`0.7W
`12 to 16VDC
`
`Input Power: Positive
`0.3W
`-12 to -16VDC
`
`Input Power: Negative
`
`40mA @ ±15VDC
`
`Input Current:
`
`RS-232
`
`Digital Output:
`
`±10VDC
`
`Analog Output:
`Per line
`300 Ohm
`
`Analog Output Impedance:
`Physical
`
`
`
`< 0.25°
`
`Axis Alignment:
`3.0 x 7.1 x 3.4 (cm)
`1.2"W x 2.8"L x 1.35"H
`
`Size: Including Mounting Flanges
`60 grams
`2.1 oz
`
`Weight:
`Mating Connector Incl.
`Amp 4-794627-2 (12 pin)
`
`Connection:
`* Actual accuracy can be calculated as the listed percentage multiplied by the change in value over the entire dynamic maneuver.
`† The Analog output range for Bank & Elevation is menu selectable. This also changes the analog scale factor for Bank & Elevation.
` Specifications are subject to change without notice.
` This product may be subject to export restrictions. Export Classification ECCN 7A994.
`
`
`
`MADE IN U.S.A
`
`Rev
`
`S/F
`Pwr.
`P/N
`
`WATSON INDUSTRIES, INC.
`
`www.watson-gyro.com
`
`X
`
`X
`
`Y
`
`Z
`
`Y
`
`Y
`
`Z
`
`X
`
`
`Dimensions:
`
`Watson Industries, Inc.
`09/20 DAO
`3035 Melby Street Eau Claire, Wisconsin 54703 U.S.A
`Phone: +1 (715) 839-0628
`Fax: +1 (715) 839-8248
`e-mail: support@watson-gyro.com Website: www.watson-gyro.com
`
`
`
`
`
`2
`
`