`
`
`
`SHORT FORM SPECIFICATIONSHORT FORM SPECIFICATION
`
`High Speed DES Engine
`64 Kbytes ROM / 16 Kbytes EEPROM / 1.3 Kbytes RAM
`ISO7816 & ISO 14443 A Interface
`Contact & Contactless Operation
`Optional MIFARE® Emulation (1K or 4K)
`TANGRAM Handshaking Technology
`
`P8RF6016
`Secure Dual Interface Smart Card IC
`Short Form Specification
`November 2003
`Revision 1.0
`
`Samsung Ex. 1013, Page 1 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`CONTENTS
`
`1
`1.1
`1.2
`1.3
`1.4
`1.5
`2
`2.1
`2.1.1
`2.1.2
`2.1.3
`3
`4
`5
`5.1
`5.1.1
`5.1.2
`
`FEATURES
`MIFARE® ProX FAMILY STANDARD FEATURES
`SECURITY FEATURES
`PRODUCT SPECIFIC FEATURES
`DELIVERY TYPES
`DESIGN IN SUPPORT
`DESCRIPTION
`Different Configurations of the P8RF6016
`Configuration A
`Configuration B1
`Configuration B4
`ORDERING INFORMATION
`BLOCK DIAGRAM
`PINNING INFORMATION
`Smart Card contacts
`Smart Card contacts Dual Interface “Standard Type”
`Smart Card Contacts Dual Interface “Plug In Type”
`
`Note:
`
` Specification may be changed without further notice.
`
`2
`
`
`
`Samsung Ex. 1013, Page 2 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`FEATURES
`1
`MIFARE® ProX FAMILY STANDARD FEATURES
`1.1
`• Enhanced ultra low power 80C51CPU, operates in
`contact and contactless mode
`• TANGRAM handshaking technology
`• High speed DPA resistant DES / DES3 engine
`– Triple-DES calculation time (incl. key load) <35 µs
`– Single-DES calculation time (incl. key load) <25 µs
`• Memory Management Unit (MMU) allows:
`– secure separation of multi applications
`– memory mapping up to 1MByte Code memory
`– Extended memory addressing system (XMA) for fast
`memory access and data transfer
`• True low power random number generator in hardware
`• ISO/IEC 7816 UART supporting standard protocols T=0
`and T=1 as well as high speed personalisation at
`1Mbit/s
`• Contact configuration and serial interface according to
`ISO/IEC 7816: GND, VCC, CLK, RST, IO1
`• contactless RF interface according to ISO/IEC14443-2
`– 13.56 MHz operating frequency
`– Reliable communication due to 100% ASK
`– High speed (106/212/424 kbit/s, efficient frame
`support)
`– true anticollision
`– 100% MIFARE®/ ISO/IEC14443 compatible
`• Contactless Interface Unit (CIU) supporting the T=CL
`protocol according to ISO/IEC14443-4 including high
`speed option (212/424 kbit/s)
`• optional free of charge MIFARE® functionality
`• MIFARE® reader infrastructure compatibility
`• High speed CRC engine according to CCITT
`• Internal CPU / coprocessor clock up to 16 / 32 MHz
`• Two 16-bit timers
`• Multiple source vectorized interrupt system with two
`priority levels
`• Error handling by customer definable exception
`interrupts
`• Multiple source reset system
`• Configurable external or internal CPU clocking
`• external clock frequency range 1 MHz to 8 MHz
`
`• High reliable EEPROM for both data storage and
`program execution
`– Bytewise EEPROM programming and read access
`– EEPROM endurance: minimum 100.000
`programming cycles per byte
`– EEPROM data retention time: 10 years minimum
`• Versatile EEPROM programming of 1 to 64 bytes at a
`time
`• Typical EEPROM page erasing time: 1.6 ms
`• Typical EEPROM page programming time: 1.6 ms
`• 2.7 V to 5.5 V extended operating voltage range
`• −25 to +85 °C operating ambient temperature range
`• Power-saving IDLE Mode
`– Wake-up from IDLE Mode by Reset or any activated
`interrupt
`• Power-saving SLEEP or CLOCKSTOP Mode
`– Wake-up from SLEEP or CLOCKSTOP Mode by
`Reset or External Interrupt
`• Additional IO ports IO2 and IO3 for full-duplex serial data
`communication; can be left unconnected if only one IO
`is required.
`
`SECURITY FEATURES
`1.2
`• Special Design measures against physical attacks
`• Power-up / Power-down reset
`• Low / high supply voltage sensor
`• Low / high clock frequency sensor
`• Low / high temperature sensor
`• EEPROM programming:
`– no external clock
`– hardware sequencer controlled
`– on-chip programming voltage generation
`• Electronic fuses for safeguarded mode control
`• Unique 4 Byte long serial number for each die
`• 16 bytes Write Once Security area in EEPROM
`• 4 bytes Read Only Security area in EEPROM
`• 64 EEPROM bytes for customer-defined security
`FabKey. Featuring batch-, wafer- or die-individual
`security data.
`• Clock input filter for protection against spikes
`• Memory protection for RAM, EEPROM and ROM
`• Custom specific EEPROM initialisation possible
`
`3
`
`
`
`Samsung Ex. 1013, Page 3 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`PRODUCT SPECIFIC FEATURES
`
`1.3
`
`• 64 Kbytes User ROM
`• 256 bytes IDATA RAM
`• up to 1024 bytes XDATA RAM
`• 16 KBytes EEPROM
`• optional free of charge MIFARE® 1K or MIFARE® 4K
`functionality
`
`DELIVERY TYPES
`1.4
`• 180 µm sawn wafer on film frame carrier (FFC)
`• Dual interface module with ISO 7816 contact pads on
`super 35 mm film (8-contact)
`• Samples in SO28 package (for new rom codes in small
`quantities only)
`
`DESIGN IN SUPPORT
`1.5
`• Development Tools
`– Keil PK51 and DK51 development tool package incl.
`µVision2/dScope C51 simulator, additional specific
`hardware drivers incl. simulation of contactless
`interface and ISO7816 card interface board.
`(www.keil.com)
`– Ashling Ultra-Emulator platform, stand alone ROM
`prototyping boards and ISO7816 and ISO14443 card
`interface board. Code Coverage and Performance
`Measurement software tools for real time software
`testing. (www.ashling.com)
`– Raisonance, RKitP51, RKitE51 Development Suite
`(includes RIDE, C-Compiler, Assembler, Simulator,
`Realtime Emulator and ISO7816 and ISO14443 card
`interface board). (www.raisonance.com)
`– EvalOS Cards and Modules for chip evaluation and
`production setup testing available in small quantities.
`– Dual Interface Dummy Modules OM6711 in
`SOT658BA1 package for implantation process
`testing available.
`• Application Support
`– Application Notes and dedicated customer
`application support engineers.
`– Customer trainings on Dual interface controllers and
`ISO14443 related topics on request
`• Software Libraries
`– Libraries supporting contactless communication
`according to ISO 14443, Part 3 and 4
`– EEPROM Read / Write routines
`– Tutorial libraries / example routines for DES engine
`
`4
`
`
`
`Samsung Ex. 1013, Page 4 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`The field proven MIFARE® RF interface technology
`(ISO14443-2) is used in all products of the MIFARE®
`interface platform and provides reliable communication
`and secure processing, even in electro-magnetically harsh
`environments like in buses or train stations. Compatibility
`with existing MIFARE® reader infrastructure and the
`optional emulation modes of MIFARE® 1K or MIFARE® 4K
`enables fast system integration and backward
`compatibility of P8RF6016 based cards.
`PHILIPS offers a unique feature free of charge on its Dual
`interface controllers, the MIFARE® 1K or 4K emulation
`providing the same functionality and performance as the
`hardwired logic contactless memory cards. The MIFARE®
`functionality can be used concurrently with ISO/IEC14443
`(T=CL) protocol based applications. This gives customers
`maximum flexibility.
`Bi-directional communication with the contact interface of
`the device can be performed through three serial interface
`IOs. These IOs are under full control of the application
`software in order to allow conditional controlled access to
`the different internal memories.
`On-chip hardware is software controlled via Special
`Function Registers (SFRs). Their function and usage is
`described in the respective sections of this specification as
`the SFRs are correlated to the activities of the CPU,
`Interrupt, IO, EEPROM, Timers, etc.
`The P8RF6016 provides two power saving modes with
`reduced activity: the IDLE and the SLEEP or
`CLOCKSTOP Mode. These two modes are activated by
`software.
`The P8RF6016 operates either with a single 3 V or 5 V
`power supply at a maximum clock frequency of 8 MHz
`supplied by the contact pads or with a power supply
`generated from the electromagnetic field emitted by a
`reader antenna.
`Operated both in contact and in contactless mode the
`users define the final function of the card with their
`operating system (OS). This allows the same level of
`security and flexibility for the contact (ISO 7816) interface
`as well as for the contactless (ISO 14443) interface.
`
`2 DESCRIPTION
`The P8RF6016 is an ultra low power secure 8-bit dual
`interface smart card controller combining contactless
`smart card technology based on the ISO14443A /
`MIFARE® contactless interface platform and contact smart
`card technology on a single chip. It is designed to support
`both high level languages like Java and multi application
`operating systems. To meet the requirements of new open
`e-purse standards like CEPS high security features are
`implemented combined with the convenience and transfer
`speed that is needed in contactless applications such as
`electronic ticketing.
`The device is manufactured in a most advanced CMOS
`process and is designed for embedding into chip cards
`according to ISO 7816. Compared to a contact only card
`an antenna has to be added in the peripheral zone of the
`card body (see Figure 1). The antenna consists of a few
`turns of a printed, etched or wired coil which is directly
`connected to the two contactless interface pads of the dual
`interface smart card module.
`To provide the highest possible degree of protection
`against hostile attacks the Philips Dual Interface Smart
`Card ICs are designed for security which requires
`continuous ongoing improvements. Philips is committed to
`this policy. Special attention was drawn to the design of the
`security architecture, in order to achieve the highest
`degree of protection against fraudulent attacks. Each
`security measure is designed to act as an integral part of
`the complete system in order to strengthen the design as
`a whole.
`The P8RF6016 is based on the 80C51 microcontroller
`family extended by additional functionality to support high
`speed memory access. This extended memory addressing
`system (XMA) is a special hardware block working like a
`co-processor and offering 16 bit functionality for the
`P8RF6016. It supports all data manipulating instructions of
`the 8051 core and can be used without additional special
`instructions.
`The device includes 64 Kbytes of ROM, up to 1.3Kbytes
`RAM (data memory) and 8 Kbytes of EEPROM, which can
`be used as data memory and as program memory. The
`non-volatile memory consists of high reliability memory
`cells to guarantee data integrity. This is especially
`important when the EEPROM is used as program memory.
`The Triple-DES co-processor speeds up the calculation
`time for Triple-DES encryption by about three orders of
`magnitude compared to software solutions and can be
`used both in contact and contactless operation. Together
`with the fast contactless interface it offers high security and
`high speed for contactless smart card applications.
`
`5
`
`
`
`Samsung Ex. 1013, Page 5 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`Fig.1 P8RF6016 Dual Interface Card.
`
`Different Configurations of the P8RF6016
`2.1
`Depending on the application requirements the P8RF6016
`can be configured in three different ways. The
`configuration has impact on the access conditions for the
`EEPROM and influences the user OS development. Three
`different configurations (A, B1 and B4) are possible and
`shown in Table 1. The following section gives a rough idea
`of the different configuration.
`
`CONFIGURATION A
`2.1.1
`In configuration A all memory resources are available and
`under full control of the dual interface User OS.
`
`CONFIGURATION B1
`2.1.2
`In configuration B1 the contactless MIFARE® Classic OS
`provided by Philips is implemented on the P8RF6016.
`1 Kbyte of the EEPROM can be accessed by the
`MIFARE® Classic OS offering the same command set and
`functionality as a MIFARE® S hardwired logic chip. The
`access conditions for the user OS to the MIFARE®
`memory area can be configured in a special section of the
`ROM code with the so called ACM (Access condition
`matrix). The MIFARE® Classic OS offers a backward
`compatibility to support existing infrastructure based on
`the MIFARE® Classic functionality.
`
`6
`
`
`
`Samsung Ex. 1013, Page 6 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`CONFIGURATION B4
`2.1.3
`Configuration B4 means that Philips provides MIFARE®
`Classic OS giving the same functionality and command set
`as given by the MIFARE® 4K chip. This emulation will be
`implemented in the ROM of the P8RF6016 and offers the
`possibility to access 4 Kbytes of EEPROM memory using
`the MIFARE® command set. Access rights for the user OS
`and the MIFARE® 4K emulation on accessing the
`EEPROM memory can be configured in a special section
`of the ROM code (ACM .. Access Condition Matrix).
`
`For secure separation of the user OS and the MIFARE®
`OS a dedicated built in hardware protection controls
`access to the EEPROM, RAM and ROM.
`For detailed explanation of MIFARE® S and MIFARE® 4K
`functionality please refer also to the following documents:
`• MIFARE® MF CM500 Product Specification
`• MIFARE® Standard IC MF1 ICS50 Functional
`Specification
`• MIFARE® Standard 4 Kbyte Card IC MF1 ICS70
`
`Table 1 Configurations of the P8RF6016
`CONFIGURATION
`A
`
`B1
`
`B4
`
`EEPROM
`
`16 KBytes for access with user OS
`14 Kbytes for access with user OS via EEPROM SFR
`1 Kbyte for access with MIFARE® Classic OS and user OS (1) (2)
`12 Kbytes for access with user OS via EEPROM SFR
`4 Kbytes for access with MIFARE® Classic OS and user OS (1) (2)
`
`Notes
`In configuration B1 and B4 the MIFARE® OS allocates 128 bytes of the CRAM at address 0480h to 04FFh
`1.
`2. For secure access a password is needed that is checked every time the user operating system (User OS) wants to
`access MIFARE® password secured EEPROM data. The user system has to call the function eePasswordRead or
`eePasswordWrite by CVEC function calls.
`
`CONFIGURATION A
`
`CONFIGURATION B1
`
`CONFIGURATION B4
`
`RAM
`1280 bytes
`
`RAM
`1152 bytes
`
`RAM
`1152 bytes
`
`128 bytes MIFARE® OS
`
`128 bytes MIFARE® OS
`
`EEPROM
`16 Kbytes
`
`ROM
`64 Kbytes
`
`EEPROM
`15 Kbytes
`
`1 Kbytes
`MIFARE® OS
`
`ROM
`64 Kbytes
`
`EEPROM
`12 Kbytes
`
`4 Kbytes
`MIFARE® OS
`
`ROM
`64 Kbytes
`
`Fig.2 Configurations of the P8RF6016.
`
`7
`
`
`
`Samsung Ex. 1013, Page 7 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`3 ORDERING INFORMATION
`Table 2 Ordering Information of the P8RF6016
`
`TYPE NUMBER(1)
`
`NAME
`P8RF6016AEW/0xxyyWz FFC
`P8RF6016AEV/0xxyyBz Module
`Module
`Plug In Type
`
`P8RF6016AEV/0xxyyCz
`
`PACKAGE
`DESCRIPTION
`sawn wafer on film frame carrier
`Dual Interface Modules on super 35 mm
`film (8-contact)
`Dual Interface Modules on super 35 mm
`film (8-contact) with Antenna connected
`to C4 and C8
`
`−
`
`SOT658BA3
`
`SOT658BA3
`
`TEMPERATURE
`RANGE (°C)
`
`-25 to +85
`
`4 BLOCK DIAGRAM
`
`CARD
`COIL
`
`LA
`
`LB
`
`IO2
`IO3
`
`ISO
`CONTACTS
`
`RF
`INTERFACE
`
`SECURITY
`SENSORS
`
`POWER-ON
`RESET
`
`VOLTAGE
`REGULATOR
`
`CLOCK INPUT
`FILTER
`
`RESET
`GENERATOR
`
`CIU
`ISO 14443
`
`EEPROM
`
`USER ROM
`
`TEST ROM
`
`RAM
`
`MEMORY-BUS
`
`CRC
`
`INTERRUPT
`SYSTEM
`
`CPU 80C51
`
` MMU
`
`UART
`ISO 7816
`
`SFR - BUS
`
`TIMERS
`
`PROGRAMMABLE
`IO 1, 2, 3
`
`16 BIT
`T0
`
`16 BIT
`T1
`
`TRUE RANDOM
`NUMBER
`GENERATOR
`
`TRIPLE-DES
`CO-PROCESSOR
`
`Fig.3 Block diagram P8RF6016.
`
`8
`
`
`
`Samsung Ex. 1013, Page 8 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`5 PINNING INFORMATION
`5.1
`Smart Card contacts
`SMART CARD CONTACTS DUAL INTERFACE “STANDARD TYPE”
`5.1.1
`
`VCC
`
`C1
`
`C5
`
`GND
`
`RST
`
`CLK
`
`N.C.
`
`C2
`
`C3
`
`C4
`
`*
`LA
`
`*
`
`LB
`
`C6
`
`C7
`
`C8
`
`N.C.
`
`IO
`
`N.C.
`
`* Antenna contacts are placed on module backside
`
`Fig.4 Contact assignments for SOT658BA1 (Standard Type).
`
`Table 3 Pin description
`ISO 7816
`CONTACTS
`SYMBOL
`C1
`VCC
`C2
`RST
`C3
`CLK
`C4
`reserved
`C5
`GND
`C6
`VPP
`C7
`IO
`C8
`reserved
`−
`−
`−
`−
`−
`−
`−
`−
`Note
`1.
`IO2, IO3 assignement on request
`
`SYMBOL
`VCC
`RST
`CLK
`N.C.
`GND
`N.C.
`IO
`N.C.
`IO2
`IO3
`LA
`LB
`
`P8RF6016
`DESCRIPTION
`Power supply voltage input
`Reset input, active LOW
`Clock input
`not connected
`Ground (reference voltage) input
`not connected
`Input/Output #1 for serial data
`not connected
`Input/Output #2 for serial data
`Input/Output #3 for serial data
`antenna coil connection
`antenna coil connection
`
`9
`
`
`
`Samsung Ex. 1013, Page 9 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors
`
`Short Form Specification Revision 1.0 November 2003
`
`Secure Dual Interface Smart Card IC
`
`P8RF6016
`
`5.1.2
`
`SMART CARD CONTACTS DUAL INTERFACE “PLUG IN TYPE”
`
`VCC
`
`C1
`
`C5
`
`GND
`
`RST
`
`CLK
`
`LA
`
`C2
`
`C3
`
`C4
`
`*
`LA
`
`*
`
`LB
`
`C6
`
`C7
`
`C8
`
`N.C.
`
`IO1
`
`LB
`
`* Antenna contacts are placed on module backside
`
`Fig.5 Contact assignments for SOT658BA1 (Plug-In-Type).
`
`Table 4 Pin description
`
`ISO 7816
`
`SYMBOL
`VCC
`RST
`CLK
`reserved
`GND
`VPP
`IO
`reserved
`
`CONTACTS
`C1
`C2
`C3
`C4
`C5
`C6
`C7
`C8
`Note
`1.
`IO3 assignement on request
`
`DUAL INTERFACE
`(“PLUG-IN TYPE”)
`SYMBOL
`VDD
`RST
`CLK
`LA
`VSS
`N.C.
`IO1
`LB
`
`P8RF6016
`
`DESCRIPTION
`Power supply voltage input
`Reset input, active LOW
`Clock input
`Antenna coil connection LA
`Ground (reference voltage) input
`not connected
`Input/Output #1 for serial data
`Antenna coil connection LB
`
`10
`
`
`
`Samsung Ex. 1013, Page 10 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`
`
`Philips Semiconductors – a worldwide company
`
`Contact information
`
`Fax: +31 40 27 24825
`For additional information please visit http://www.semiconductors.philips.com.
`For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.
`
`
`
`© Koninklijke Philips Electronics N.V. 2002
`
`SCA74
`
`All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
`The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
`without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
`under patent- or other industrial or intellectual property rights.
`
`Samsung Ex. 1013, Page 11 of 11
`Samsung Electronics America, Inc. v. RFCyber Corp.
`IPR2021-00980
`
`