`
`Texas Instruments Incorporated
`
`An introduction to the Wireless Power
`Consortium standard and TI’s
`compliant solutions
`
`By Bill Johns
`Senior Applications Engineer
`Introduction
`Wireless power is beginning to show great potential in the
`consumer market. The ability to power an electronic
`device without the use of wires provides a convenient
`solution for the users of portable devices and also gives
`designers the ability to develop more creative answers to
`problems. This technology’s benefits can be seen in the
`many portable devices, from cell phones to electric cars,
`that normally operate on battery power.
`Inductive coupling is the method by which efficient and
`versatile wireless power can be achieved. For ease of use
`and the benefit of both designers and consumers, the
`Wireless Power Consortium (WPC) has developed a
`standard (see Reference 1) that creates interoperability
`between the device providing power (power transmitter,
`charging station) and the device receiving power (power
`receiver, portable device). Established in 2008, the WPC is
`a group of Asian, European, and American companies in
`diverse industries, including electronics manufacturers
`and original equipment manufacturers (OEMs). The WPC
`standard defines the type of inductive coupling (coil con-
`figuration) and the communications protocol to be used
`for low-power wireless devices. Any device operating
`under this standard will be able to pair with any other
`WPC-compliant device. One key benefit to this approach is
`
`that it makes use of the coils for communications between
`the power transmitter and the power receiver. See Figure 1
`for a typical application diagram.
`WPC standard for wireless power
`Under the WPC standard, “low power” for wireless transfer
`means a draw of 0 to 5 W. Systems that fall within the
`scope of this standard are those that use inductive coupling
`between two planar coils to transfer power from the power
`transmitter to the power receiver. The distance between
`the two coils is typically 5 mm. Regulation of the output
`voltage is provided by a global digital control loop where
`the power receiver communicates with the power trans-
`mitter and requests more or less power. Commu ni ca tion is
`unidirectional from the power receiver to the power trans-
`mitter via backscatter modulation. In backscatter modula-
`tion, the power-receiver coil is loaded, changing the current
`draw at the power transmitter. These current changes are
`monitored and demodulated into the information required
`for the two devices to work together.
`The WPC standard defines the three key areas of the
`system—the power transmitter that will supply power, the
`power receiver that will use the power, and the communi-
`cations protocol between the two devices. These three
`areas are explored next.
`
`Figure 1. Typical wireless-power functional diagram
`
`Transmitter
`
`Power
`
`Receiver
`
`AC to DC
`
`Drivers
`
`Rectification
`
`Voltage
`Conditioning
`
`Load
`(Phone or
`Battery)
`
`Communication
`
`Controller
`
`V/I
`Sense
`
`Controller
`
`10
`
`High-Performance Analog Products
`
`www.ti.com/aaj
`
`1Q 2011
`
`Analog Applications Journal
`
`Apple v. GUI Global Products
`IPR2021-00471, 472, 473
`GUI Ex. 2032
`
`
`
`Texas Instruments Incorporated
`
`Power Management
`
`Power transmitter
`The direction of power transfer is always from the power
`transmitter to the power receiver. The key circuits of the
`power transmitter are the primary coil, used to transfer
`power to the power-receiver coil; the control unit for
`driving the primary coil; and the communications circuit
`for demodulating the voltage or current from the primary
`coil. Flexibility of the power-transmitter design is limited
`to provide consistent power and voltage levels to the
`power receiver.
`The power receiver identifies itself to the power trans-
`mitter as a compliant device and also provides configura-
`tion information. Once the transmitter initiates power
`transfer, the power receiver sends error packets to the
`power transmitter requesting more or less power. The
`power transmitter stops supplying power upon receiving
`an “End Power” message, or if no packets are received
`for more than 1.25 seconds. While no power is being
`transmitted, the power transmitter enters a low-power
`standby mode.
`The WPC specification allows for both fixed- and moving-
`coil configurations. A single fixed coil, referred to as type
`A1, is the solution that Texas Instruments (TI) supports.
`The power transmitter, typically a flat surface upon
`which the user places the power receiver, is connected to
`the power source. The coils of a WPC-compliant device
`operate as a resonant half bridge on a 50% duty cycle,
`with a 19-VDC input (±1 V). If more or less power is
`needed at the power receiver, the frequency in the coil
`changes but stays between 110 and 205 kHz, depending
`on power demands.
`Power receiver
`The power receiver is typically a portable device. The key
`circuits of the power receiver are the secondary coil, used
`to receive power from the power-transmitter coil; the rec-
`tification circuit, used to convert AC to DC; the power-
`conditioning circuit, which buffers the unregulated DC
`into regulated DC; and the communications circuit, which
`modulates the signal to the secondary coil. The power
`receiver is responsible for all communications of its
`authentication and power requirements, as the power
`transmitter is only a “listener.”
`While design of the power transmitter is restricted to
`keep it WPC-compliant, much more freedom is permitted
`for designing the power receiver. The coil dimension of the
`power receiver can be adjusted to meet the device’s form
`factor. The coil voltage at the power receiver is full-wave
`rectified, with a typical efficiency of 70% for a 5-V, 500-mA
`output. Because communication between the two devices
`is unidirectional, the WPC selected the power receiver to be
`the “talker.” Inductive power transfer works by coupling a
`magnetic field from primary to secondary coils. Uncoupled
`field lines rotate around the primary coil and do not repre-
`sent loss as long as the field lines don’t couple a parasitic
`load (for example, eddy-current loss in metal).
`
`Communications protocol
`The communications protocol includes analog and digital
`pinging; identification and configuration; and power trans-
`fer. A typical start-up sequence that occurs when a power
`receiver is placed on a power transmitter proceeds as
`follows:
`1. An analog ping from the power transmitter detects the
`presence of an object.
`2. A digital ping from the power transmitter is a longer
`version of the analog ping and gives the power receiver
`time to reply with a signal-strength packet. If the signal-
`strength packet is valid, the power transmitter keeps
`power on the coil and proceeds to the next phase.
`3. During the identification and configuration phase, the
`power receiver sends packets that identify it and that
`provide configuration and setup information to the
`power transmitter.
`4. In the power-transfer phase, the power receiver sends
`control error packets to the power transmitter to
`increase or decrease the power supply. These packets
`are sent approximately every 250 ms during normal
`operation or every 32 ms during large signal changes.
`Also during normal operation, the power transmitter
`sends power packets every 5 seconds.
`5. To end the power transfer, the power receiver sends an
`“End Power” message or sends no communications for
`1.25 seconds. Either of these events places the power
`transmitter in a low-power state.
`TI’s WPC-compliant solutions
`TI is a founding member of the WPC and has taken an
`active role in developing a robust wireless-power specifica-
`tion. TI has developed reliable solutions for both a power
`receiver and a power transmitter in the form of three newly
`developed ICs. The power receiver uses the MSP430bq1010
`and bq25046 devices. The power transmitter is based on
`the bq500110, which supports type A1 (single-coil) config-
`urations. Both receiver and transmitter ICs are designed
`to be interoperable with other WPC-compliant solutions.
`The MSP430bq1010 in the power receiver handles all
`of the logic functions and communications. The onboard
`analog-to-digital converters monitor the levels of voltage
`into and current out of the bq25046. The bq25046 provides
`load-current information to the MSP430bq1010, which then
`uses this information to control the power transmitter’s
`operating point. The bq25046 provides a low-current, 3.3-V
`low-dropout regulator (LDO) to power the MSP430bq1010
`and logic circuit, while a larger 5.0-V LDO is capable of
`providing up to 1 A of current to the main output.
`The power-transmitter solution is provided with the
`bq500110. This device demodulates and decodes serial
`data from the power receiver. The control circuits first
`
`Analog Applications Journal
`
`1Q 2011
`
`www.ti.com/aaj
`
`High-Performance Analog Products
`
`11
`
`Apple v. GUI Global Products
`IPR2021-00471, 472, 473
`GUI Ex. 2032
`
`
`
`Power Management
`
`Texas Instruments Incorporated
`
`TI Lit. #
`
`Document Title
`2. “Wireless Power Transmitter Manager,”
`bq500110 Data Sheet. . . . . . . . . . . . . . . . . . . . . . slusae0
`3. “1.1A, Single-Input 5-V Power Supply IC
`for Wireless Power Applications,” bq25046
`Data Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . slusa83
`4. “Wireless Receiver-Side Communication and
`Power Monitoring IC for Wireless Power,”
`MSP430bq1010 Data Sheet. . . . . . . . . . . . . . . . . slas696
`5. “bq500110EVM-688 Evaluation Module,”
`User’s Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . slvu429a
`6. “bq25046EVM-687 Evaluation Module,”
`User’s Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . slvu420
`Related Web sites
`www.ti.com/wirelesspower
`www.ti.com/sc/device/partnumber
`Replace partnumber with bq25046, bq500110, or
`MSP430bq1010
`
`certify that the power receiver is indeed a WPC-compliant
`device, then configure the power transmitter accordingly.
`TI’s BQTESLA100LP EVM kit combines separate trans-
`mitter and receiver designs into a single kit that includes
`mechanical packaging. This kit can be used for evaluation
`of the ICs or as a design example. The WPC has certified
`that both the power-transmitter and the power-receiver
`solutions meet the Version 1.0 specification. No software
`is required to operate the EVM, which needs only a 19-V
`input. The EVM kit’s output will be 5 V at up to 1 A. The
`transmitter EVM includes multiple LED options for visual
`indication of power-transmission status. Also, two buzzer
`options provide audio indication of the start of power
`transfer.
`Conclusion
`The WPC standard is a set of guidelines that allows manu-
`facturers to develop solutions with the confidence that
`their components will mesh with a variety of other WPC-
`certified components designed for inductive power transfer.
`References
`For more information related to this article, you can down-
`load an Acrobat® Reader® file at www.ti.com/lit/litnumber
`and replace “litnumber” with the TI Lit. # for the
`materials listed below.
`
`Document Title
`1. Wireless Power Consortium. “System
`Description Wireless Power Transfer, Vol. 1,
`Part 1,” Version 1.0 [Online]. Available:
`http://www.wirelesspowerconsortium.com/
`downloads/wireless-power-specification-
`part-1.html
`
`TI Lit. #
`
`—
`
`12
`
`High-Performance Analog Products
`
`www.ti.com/aaj
`
`1Q 2011
`
`Analog Applications Journal
`
`Apple v. GUI Global Products
`IPR2021-00471, 472, 473
`GUI Ex. 2032
`
`
`
`TI Worldwide Technical Support
`
`Internet
`TI Semiconductor Product Information Center
`Home Page
`support.ti.com
`
`TI E2E™ Community Home Page
`e2e.ti.com
`
`Product Information Centers
`Americas Phone
`+1(972) 644-5580
`Brazil
`Mexico
`
`Phone
`
`0800-891-2616
`
`Phone
`
`0800-670-7544
`
`
`
`
`Fax
`Internet/Email
`
`+1(972) 927-6377
`support.ti.com/sc/pic/americas.htm
`
`Europe, Middle East, and Africa
`Phone
` European Free Call
`
`
`
`International
` Russian Support
`
`00800-ASK-TEXAS
`(00800 275 83927)
`+49 (0) 8161 80 2121
`+7 (4) 95 98 10 701
`
`
`
` Note: The European Free Call (Toll Free) number is not active
`in all countries. If you have technical difficulty calling the free
`call number, please use the international number above.
`
`Fax
`Internet
`Direct Email
`
`Japan
`Phone
`Fax
`
`Internet/Email
`
`
`+(49) (0) 8161 80 2045
`support.ti.com/sc/pic/euro.htm
`asktexas@ti.com
`
`Domestic
`International
`Domestic
`International
`Domestic
`
`0120-92-3326
`+81-3-3344-5317
`0120-81-0036
`support.ti.com/sc/pic/japan.htm
`www.tij.co.jp/pic
`
`Asia
`Phone
`+91-80-41381665
`
`International
`Toll-Free Number
` Domestic
`
`
` Note: Toll-free numbers do not support
`mobile and IP phones.
` Australia
`1-800-999-084
`
` China
`800-820-8682
`
` Hong Kong
`800-96-5941
`
`
`India
`1-800-425-7888
`
`
`Indonesia
`001-803-8861-1006
`
` Korea
`080-551-2804
`
` Malaysia
`1-800-80-3973
`
` New Zealand
`0800-446-934
`
` Philippines
`1-800-765-7404
`
` Singapore
`800-886-1028
`
` Taiwan
`0800-006800
`
` Thailand
`001-800-886-0010
`
`Fax
`+8621-23073686
` tiasia@ti.com or ti-china@ti.com
`Internet
`support.ti.com/sc/pic/asia.htm
`
`Important Notice: The products and services of Texas Instruments Incorporated and
`its subsidiaries described herein are sold subject to TI’s standard terms and conditions
`of sale. Customers are advised to obtain the most current and complete information
`about TI products and services before placing orders. TI assumes no liability for
`applications assistance, customer’s applications or product designs, software
`performance, or infringement of patents. The publication of information regarding any
`other company’s products or services does not constitute TI’s approval, warranty or
`endorsement thereof.
`
`E2E is a trademark of Texas Instruments. Acrobat and Reader are registered trademarks of
`Adobe Systems Incorporated. All other trademarks are the property of their respective owners.
`
`A122010
`
`© 2011 Texas Instruments Incorporated
`
`SLYT401
`
`Apple v. GUI Global Products
`IPR2021-00471, 472, 473
`GUI Ex. 2032
`
`
`
`IMPORTANT NOTICE
`
`Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
`and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
`obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
`sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
`TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
`warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
`mandated by government requirements, testing of all parameters of each product is not necessarily performed.
`TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
`applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
`adequate design and operating safeguards.
`TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
`or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
`published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
`warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
`property of the third party, or a license from TI under the patents or other intellectual property of TI.
`Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
`by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
`business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
`restrictions.
`Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
`express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
`responsible or liable for any such statements.
`TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
`be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
`such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
`acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
`and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
`provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
`such safety-critical applications.
`TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
`specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
`specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
`the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
`TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
`designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
`products in automotive applications, TI will not be responsible for any failure to meet such requirements.
`Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
`
`Products
`Audio
`Amplifiers
`Data Converters
`DLP® Products
`DSP
`Clocks and Timers
`Interface
`Logic
`Power Mgmt
`
`www.ti.com/audio
`amplifier.ti.com
`dataconverter.ti.com
`www.dlp.com
`dsp.ti.com
`www.ti.com/clocks
`interface.ti.com
`logic.ti.com
`power.ti.com
`
`microcontroller.ti.com
`Microcontrollers
`www.ti-rfid.com
`RFID
`RF/IF and ZigBee® Solutions www.ti.com/lprf
`
`Applications
`Communications and Telecom www.ti.com/communications
`Computers and Peripherals
`www.ti.com/computers
`Consumer Electronics
`www.ti.com/consumer-apps
`Energy and Lighting
`www.ti.com/energy
`Industrial
`www.ti.com/industrial
`Medical
`www.ti.com/medical
`Security
`www.ti.com/security
`Space, Avionics and Defense www.ti.com/space-avionics-defense
`Transportation and
`www.ti.com/automotive
`Automotive
`Video and Imaging
`Wireless
`
`www.ti.com/video
`www.ti.com/wireless-apps
`
`TI E2E Community Home Page
`
`e2e.ti.com
`
`Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
`Copyright © 2011, Texas Instruments Incorporated
`
`Apple v. GUI Global Products
`IPR2021-00471, 472, 473
`GUI Ex. 2032
`
`