`
`SHARP
`
`OPTOELECTRONIC DEVICES DIVISION
`ELECTRONIC COMPONENTS GROUP
`SHARP CORPORATION
`
`SPECIFICATION
`
`DEVICE SPECIFICATION FOR
`
`MODEL No.
`
`Infrared Detecting unit for Remote Control
`
`GPIUV7OQS series
`
`Specified for
`
`Enclosed please find copies ofthe Specifications which consists of 12 pages including cover.
`After confirmation ofthe contents, please be sure to send back D copies ofthe Specificafions
`with approving signamre on each.
`
`CUSTOMERS APPROVAL
`
`'
`
`'
`
`PRESENTED
`
`DATE
`
`BY
`
`DATE
`
`‘
`
`BY
`
`AZ _ 0
`
`H. Ogura,
`Department General Manager of
`Engineering Dept,III
`Opto-EIectronic Devices Div.
`ELECOM Group
`SHARP CORPORATION
`
`Roku EX1011
`
`US. Patent No. 7,589,642
`
`Roku EX1011
`U.S. Patent No. 7,589,642
`
`i
`
`
`
` Product name :
`
`Inii’ared Detectin unit for Remote Control
`'
`
`1/11
`
`Model No. : GPlUV70g 23 series
`
`
` 1. These specification sheets include materials protected under copyright of Shell) Corporation ("Sharp“).
`
`Please do not reproduce or cause anyone to reproduce them without Sharp's consent.
`
`2, When using this product, please observe the absolute maximtnn ratings and the instructions for use outlined
`in these specification sheets, as well as the precautions mentioned below.
`Sharp assumes no responsibility
`for any damage resulting from use of the product which does not comply with the absolute maximum ratings
`
`and the instructions included in these Specification sheets, and the precautions mentioned below.
`
`' 0A equipment
`
`' Telecommunicationequipment(Terminal)
`
`' Audio visual equipment
`
`' Home appliances
`
`]
`
`
`
`
`
`
` (Precautions)
`
`(1) This product is designed for use in the following application areas ;
`
`
`
`
`Ifthe use ofthe product in the above application areas is for equipment listed in paragraphs
`(2) or (3), please be sure to observe the precautions given in those respective paragraphs.
`
`
`
`
`
`
`
`(2) Appropriate measures, such as fail-safe design and redtmdant design considering
`the safety design of the overall system and equipment, should be taken to ensure reliability
`and safety when this product is used for equipment which demands high reliability and
`safety in function and precision, such as ;
`
`
`
`
`
`
`
`
`
`
`
`- Transportation control and safety equipment (aircraft, train, automobile etc.)
`
`' Gas leakage sensor breakers
`' Trafiic signals
`' Other safety equipment
`etc.
`
`' Rescue and security equipment
`
`(3) Please do not use this product for equipment which require extremely high reliability
`and safety in fiinction and precision, such as ;
`
`' Space equipment
`
`' Telecommunication equipment (for trunk lines)
`
`' Nuclear power control equipment
`
`' Medical equipment
`
`etc.
`
`regarding interpretation ofthe above three paragaphs.
`
`(4) Please contact and consult with a Sharp sales representative if there are any questions
`
`
`
`3. Please contact and consult with a Sharp sales representative for any questions about this product;
`
`
`
`
`1. Application
`This specifications applies to the model marked "O"in the following models ofinfrared detecting unit 0 c!
`
`
`
`E e I 244A GPlUV70QS series
`I ecemher 27, 2002
`
`2/11
`
`“ ‘-
`
`The model list of GPlUV’l'OQS series
`
`
`
`——_
`———
`
`_——
`
`— GPlUV702QS
`36.7
`kHz
`
`
`
`Main application: TV set, VCR, Radio cassette recorder, Stereo
`
`to
`
`Outline
`
`Refer to the attached sheet, Page 8.
`
`3. Ratings and characteristics
`
`Refer to the attached sheet, Page 4 to 7.
`
`4. Reliability
`
`Refer to the attached sheet, Page 9.
`
`5. Outgoing inspection
`
`Refer to the attached sheet, Page 10.
`
`6.
`
`Supplement
`
`1) This infrared detecting unit for remote control satisfies each performance requirements in para. 3.5,
`in the standard optical system in Fig.2.
`
`2)
`
`3)
`4)
`
`5)
`
`6)
`
`7)
`
`This product is built-in photodiode.
`
`Product mass : Approx. 0.7g
`
`This product shall not contain the following materials.
`
`Also, the following materials shall not be used in the production process for this product
`Materials for ODS : CFC5, Halon, Garcon tetrachloride, 1.1.1-Trichloroethane (Methyl chloroform)
`Brominated flame retardants
`
`Specific brominated flame retardants such as the PBBOS and PBBS are not used in this device at all.
`
`Packing specification :
`
`Refer to the attached sheet, Page 11.
`
`Country of origin 2 Philippine, Indonesia
`
`7. Notes
`
`1) Transmitting code
`When this infiared remote control detecting unit shall he adopted for Wireless remote control, please use it with the signal format
`oftransmitter, which total duty ratio Dt (Emitting time NE tN I Transmitting time for 1 block T)is 40% or less. ON signal time
`Ton (Pulse width ofthe presence ofmodulated 1R) should be 250 n s or more.
`In case that the signal format oftotal duty
`and ON signal time is out ofabove conditions, thereIs a case that recepu'on distanceis much reduced or output is not appeared
`
`Transmittin time for 1 block : T
`
`
`
`BL: (WH tN/T) x100 (%)
`
`
`
`3/11
`
` 2) Transmitter
`
`characteristics and operating condition ofthe light emitting element and the characteristics ofthis light detecting unit.
`
`3) Detector face and cleaning
`Ifthe surface of detector is smeared with dust or dirt, it may cause faulty operation. Caution shall be taken to avoid this.
`And do not touch the detector surface.
`Ifthe surface was smeared, wipe it clean with soft cloth,
`
`Ifany solvent is needed, Methyl alcohol, Ethyl alcohol, or lsopropyl alcohol should be used.
`Please don't carry out washing. Because, alter washing the remainder in solvent or flux in this device cause malfimction
`
`Marking on this device is defaced by washing.
`
`4) Mounting this product
`' The shield case shall be grounded on the PCB pattern.
`
`(There are two cases that shield case and GND pin are connected in the shield case, or are not connected in it.)
`' It shall not be applied the terminal and case with unnecessary stress.
`
`- Please don't push the detecting side (photodiode) from external.
`
`- In order to prevent electrostatic discharge of integrated circuit, human body and soldering iron, etc. shall be grounded
`' The holes and the slits on the inflated detecting unit shall not be used as the other purpose to maintain its performance.
`
`' When mounting, please mount the external circuit below. (CR filter)
`
`(External parts should be mounted as close as possrble to the sensor.)
`
`C1=47 a F
`
`(Circuit fixed number)
`R1=47 9 i5%
`
`It is difference fi-om mounting equipment. Please select it by your mounting equipment
`The circuit constant is 5. example.
`This device has a transistor as protection element between Vcc and GND to improve anti-static electricity proof.
`
`Please be carefully not to apply exceeding the absolute maximum ratings of applying voltage and continuous high voltage
`
`Spike noise because there is cases that transistor will be short by secondary breakdown generally.
`In order to do diflicultly, Please add CR filter (47 Q (1/10W), 10 [.L F or more) such as external circuit example above near Vcc.
`
`5) Characteristics ofthis product
`
`- There is a possibility that noise on output may be caused by environmental condition etc.
`
`even ifthere is no input transmission signal.
`
`' Please shall confirm operation or your actual machine. Because the output pulse width ofthis product is fluctuated
`
`by environmental conditions such as signal format, temperature, distance from transmitter, and so on.
`
`6)
`
`Soldering
`- In case that this product is kept in high humidity condition, it may be hard to solder, please be careful enough
`about storage method. Depend on the flux you select, there are difierent solderabilities, so please select a suitable flux and use it.
`° Please don’t do soldering this product by reflow.
`- Please make sure in case ofhand soldering that you use the solder iron with less than 45W power and the solder iron point (edge)
`
`temperature is less than 320°C within 3 seconds, and also don't add any force to lead flame directly.
`- Please make sure also you check the mountability prior to the process since the solder portion between the case and the lead frame
`
`may be detached due to the heat when soldering.
`
`
`
` 7) Use condition
`
`Please use this device away from the dew drop. Be aware that the dew drop rusts shield case and others,
`
`may affect the electric characteristics.
`
`8) Output circuit
`In case output ofVout (Voltage ofVoh in the below chart) decreases due to influence fiom the external circuit,
`please adjust the circuit constants so that Voh is kept more than 2.8V.
`
`EX.) When adding transistors to output circuit, they shall he added
`as R1, R2 shown on the light chart & their value
`
`shallbe adjusted so thatVohbecomes 2.8V ormore.
`
`CRL=ahout 100k 9)
`
`9) Outlook of device
`The lead flame may be deformed since the device is packed in vinyl bag.
`
`
`
`
`
` 3. Ratings and chaiactefisfics
`
`3.1
`
`Schematic
`
`5/11
`
`4%
`
`RL
`
`> I?
`
`Com—
`
`Amp
`
`Limiter
`
`BP.F
`
`Demodulator
`
`Integtator parator
`
`I
`
`C
`
`.
`
`GND Vcc Vout
`
`3.2 Absolute maximum ratings
`
`symbol
`
`
`
`
`
`
`
`
`
`—-—-
`0°C"
`
`
`WWW —-
`
`
`
`X1) No dew drop
`
`>242)
`
`1.6mm at mounting on single-sided PCB
`
`
`
`3.3 Recommended operating conditions
`
` Supply voltage
`
`
`
`>243) The burst wave as shown in the figure
`ontherightshallbe tIansmitted
`by the tansmitter shown in Fig. 1.
`However, the carrier frequency
`oftransmitteris sameas X4kHz
`Measuring shallbefromjust
`after starting the u'ansmission until 50 pulse.
`
`fo =>Z<4 Duty 50%
`_ M
`Transnfissive signal
`
`011?“ signal
`
`600145 1000M
`—\—'—‘—I_
`
`T2
`
`T1
`
`
`
`6/11
`
`I O S series
`
`
`
`
`——
`
`
`
`
`
`
`
`
`
`
`
`3.5 Performance
`
`The output signal ofthis infiared detecting unit shall satisfy the following requirements with the transmitter shown in Fig.1 used
`in the standard optical system in Fig.2.
`
`3.5.1 Characteristics of linear reception distance
`
`The output signal shall satisfy the electrical characteristic requirements in para. 3.4
`at L'—'0.2 to 8.5m, (X5) Ev<101x, ¢=O° in Fig.2.
`
`3.5.2 Characteristics of sensitivity angle reception distance
`
`The output signal shall satisfy the electrical characteristic requirements in para. 3.4
`at L=O.2 to 6.0m, (>265) Ev<101x,
`qb §30° in Fig.2.
`
`3.5.3 Characteristics of anti-outerperipheral light reception distance
`
`The output signal shall satisfy the electrical characteristic requirements in para. 3.4
`at L=O.2 to 4.0m, (X5, X6)Ev§3001x, ¢=0° in Fig.2.
`
`It refers to detector face illuminance.
`9K5)
`>246) Outer peripheral light source : CIE standard light source A shall be used and placed at 45° fiom the perpendicular axis
`at the detector face center.
`
`
`
`ED—02244A GPlUV'i'OQS series
`December 27, 2002
`
`7/ l 1
`
`Transmitter (The GL521 is used)
`
`fn=§<4
`Duty 50%
`
`Oscilloscope
`
`In the figure above, the transmitter shall be set as the outputVO‘th (p—p) will be 40mV.
`Note that the PD49PI in this application is the One with short-circuit current
`
`Isc=2.6 uAmeasured at Ev=100]x.
`
`(Ev is the iflm-ninance by GE standard light source A (tungsten 1311113)).
`
`Fig. 1 Transmitter
`
`
`
`Detector face illuminance : Ev
`
`Transmitter
`
`Reception distance: L
`
`
`
`
`
`( (b ; indicates horizontal and vertical directions)
`
`Fig.2 Standard optical system
`
`
`
`
`
`
`
`
`
`
`Production place
`
`
`
`
`
`
`ED-0224-4A GPlUV7OQS series
`.
`December 27, 2002
`
`8/11
`
`x.)
`
`12 91
`
`I L— Week(1 to 6)
`
`Month (1 t09, X,Y,Z)
`
`Year (2002: 2)
`
`The"-"maflcinside 0 shows
`
`production place. (*3)
`
`Cmedseal
`
`a:
`
`g
`
`3mm
`
`
`
`
`
`
`
`
`I'llmfiwfi\‘1:‘fla§§
`
`ris\\':\’1~:1
`
`
`
`
`
`
`EXample of mounting drawing
`from solder side
`(Reference)
`
`
`
`
`
`Top of lens
`
`*1 :
`Indicates root dimensions of connector
`Unspecified tolerance 1 i 0.3
`Case thickness :
`0.3TYP.
`Case material : Fe
`
`wwyowswwe
`
`Solder plating (Sn7 Pb)
`Case finish :
`Lead material : Fe (Ag plating)
`Lead finish :
`Solder dip (Sn, Ag, Cu).
`Mold resin : Epoxy resin
`. Product mass : Approx. 0.7g
`10.
`*2 : Exclude sagged solder
`1 1.
`*3 : The “ — ” mark above lot number indicate production place.
`(Production country is referred to the production place list)
`12. W : The portion indicates soldering connection area
`between case and leads.
`
`‘
`
`
`
`
`
`
`However, it never short with other flame.
`
`
`13.
`portion may have some solder balls by GND soldering.
`Solder adhesives shouldbe acceptable.
`1=l/1mm
`
`
`3
`
`
`Scale
`[,1
`
`Name
`
`‘
`GPIUV 70QS senes
`Outline Dimensions
`
`RUD2903B
`
`
`
`
`
`
`
`9/11
`
`44A GPIUV7OQS series
`ber 27, 2002
`
`4. Reliability
`
`The reliability ofproducts shall satisfy items listed below.
`
`Confidence level :
`LTPD : 10 or 20
`
`Test Items
`
`.
`.
`Test Conditions
`
`Failure Judgement
`.
`
`Twat Strength
`(Tens1ou)
`
`Terminal strength
`(Bending)
`Sh ck
`o
`
`Weight: 5N,
`
`3OS/each terminal
`
`
`
`n—11,c=0
`
`Weight : 2.5N
`0°
`-90° -0°
`,
`2 times / each terminal
`Acceleration: 1000111/52,
`6ms
`3 directions I 3 times
`
`
` n=11, C=0
`
`n=11,C=0
`
`
`
`
`
`
`
`
`._- Defectide)
`
`
`
`
`
`
`Variable frequency
`vibration
`
`Frequency range : 10 to SSHfl sweep 1min
`Overall amplitude : 1.5mm X, Y, 2/211 each
`
`
`
`n=11, C=O
`
`
`
`
`
`
`should not be satisfied n=22, C=O
`
`
`
`* High temp. and high
`humidity storage
`* High temp. storage
`
`
`
`
`* Temperature cycling
`
`
`
`0
`"Fa—40 C 90 /uRH,
`Ta=70°C,
`1:240h
`we Fm
`
`1—24011
`
`Performance test
`
`in para. 3.5
`
`
`
`lcycle
`
`40°C to +70°C
`(30min)
`(30min)
`20 cycles test
`
`
`
`*Operatiou life
`(High temperature)
`Solderheat
`
`_ 0
`Tat—70 C, Vcc=5V,
`2609C”
`SS
`(1 .6mm at mounting on single-sided PCB)
`
`t=240h
`
`In the test *mark above, the sample to be tested shall be left at normal temperature and humidity for 2hours
`afier it is taken out ofthe chamba. (No dew drop)
`
`Solderable —a-
`
`
`
`5. Outgoing inspection
`
`(1)
`
`Inspection lot
`
`Inspection shall be canied out per each delivery lot.
`
`(2)
`
`Inspection method
`
`r. 90.224414 GPlUV'i'OQS series
`
`10/11
`
`
`
`FE
`
`.-mber27,2002
`
`A single sampling plan, normal inspection level II based on ISO 2859 shall be applied.
`
`
`' Electricalcharacteristicdefect ofV0“,VOL,T] andT2inpara, 3.4.
`
`J _ceptforGNDterminal)
`
`Ma'01.defect I.Distancebetween—ignalterminalandshieldcase(02111111ormore)
`I.Itshouldhavenoremadsablestainsandcracksthatgive
`
`.Defonnationofshieldcase.(Satisfyingoutlinedimensions ofItem2)
`
`any influence of eleenical characteristic on light detecting.face
`
`
`
`
`
`
`
`Mmordefect
`
`
`
`
`
`
`
`Stamp, Carvedseal
`(It should be possible to read stamp and carved seal ofitem 2.
`Stamp and carved seal shouldbe indicated at fixed position.)
`
`
`
`
`
`
`
`December 27, 2002
`
`ED-02244A GPlUV'IOQS series
`
`11/11
`
`
`
`
`Product
`
`
`
`
`
`
`Antistatic electricity bag
`with device rolled
`
`with moltprain (4 rolls)
`
`
`
`Antistatic electricity bag
`
`piggy
`(Polyethylene)
`Fig.1
`
`
`Packing case
`(Corrugated cardboard)
`
`
`
`Antistatic electricity bag with device (content lOOpcs.)
`
`
`
`
`
`Model No.
`
`Quantity
`Lot No.
`
`Packaging method
`
`_
`
`3.
`
`Seal the packing box , and piint the model No., quantity and lot No.
`
`
`(Fig. 1)
`1. Put products of 100pcs. in the antistatic electricity bag.
`2. 4 rolls with 2 moltoprain based on 1 are packed in packing box.
`(Fig. 2)
`
`
`
`(Flg. 3)
`(W5. 1’ a packing box)
`- Product mass at 400pcs./package : Apprmdmately 310g
`
`
`
`
`
`
`
`
`Name
`
`GPlUV70QS sexies
`Packing specification
`
`
`
`
`
`RUD2904A
`
`