`
`TechSearch (“WTS”), located at 215 North Randall Avenue, Madison Wisconsin,
`
`53706. WTS is an interlibrary loan department at the University ofWisconsin—
`
`Madison.
`
`1 have worked as a librarian at the University of Wisconsin library
`
`system since 1998.
`
`I have been employed at WTS since 2002, first as a librarian
`
`and, beginning in 201 1, as the Director. Through the course of my employment. l
`
`have become well informed about the operations of the University of Wisconsin
`
`library system, which follows standard library practices.
`
`This Declaration relates to the dates of receipt and availability of the
`
`following:
`
`Wright, DR et al. "A closed-loop temperature control
`system for a low-temperature etch chuck." Advanced
`Techniques for Integrated Circuit Processing [1, SPIE
`Proceedings, v. 1803, 1992, p. 321-329
`
`
`Standard ogeraring Qrocedw‘es for Periodicals at the Universig.2 of
`
`Wisconsin-Madison. When an individual issue of a periodical was received by the
`
`Library, it would be checked in, stamped with the date of receipt, added to library
`
`holdings records, and made available to readers as soon after its arrival as possible.
`
`The procedure normally took a few days or at most a few weeks.
`
`Exhibit A to this Declaration is a true and accurate copy ofAdvanced
`
`Techniques for Integrated Circuit Processing 11, from the University of Wisconsin-
`
`Madison Library collection. A date stamp on the cover of this copy indicates that
`
`1
`
`Page 1 of 14
`
`Samsung Exhibit 1021
`
`
`
`Page 1 of 14
`
`Samsung Exhibit 1021
`
`
`
`this volume, published in 1993, was received by the Kurt F. Wendt Library,
`
`College of Engineering, University of Wisconsin, on June 23, 1993.
`
`Based on the information in Exhibit A, it is clear that the volume was
`
`received by the library on or before June 23, 1993, catalogued and available to
`
`library patrons within a few days or at most a few weeks after June 23, 1993.
`
`I declare that all statements made herein of my own knowledge are true and
`
`that all statements made on information and belief are believed to be true; and
`
`further that these statements were made with the knowledge that willful false
`
`statements and the like so made are punishable by fine or imprisonment, or both,
`
`under Section 1001 of Title 18 of the United States Code.
`
`Date: June 8, 2016
`
`Rachel J.
`
`atters
`
`'
`
`Wisconsin TechSearch
`
`Director
`
`Wendt Commons Library
`215 North Randall Avenue
`
`Madison, Wisconsin 53 706
`
`Page 2 of 14
`
`[\J
`
`Page 2 of 14
`
`
`
`
`EXHIBIT A
`
`
`
`
`
`‘
`
`PROCEEDINGS '
`@ SPlE—The International Society for Optical Engineering
`
`Advanced Techniques for
`Integrated Circuit Processing ll
`
`lames Bondur
`Gary Castleman
`lloyd ll. Harriett
`Terry R. Turner
`Chairstdr'tors
`
`21-23 September 1992
`San lose, California
`
`REG Ner-
`
`JUN
`
`E33"?
`
`UNWE3€8i
`
`313;;
`
`
`
`Volume 1803
`
`Page 3 of 14
`
`EXHIBIT A
`
`Page 3 of 14
`
`
`
`EXHIBIT A
`
`PROCEEDINGS
`SPiE—The International Society for Optical Engineering
`
`Advanced Techniques for
`Integrated Circuit Processing ll
`
`James Bondur
`Gary Castleman
`Lloyd R. Harriott
`Terry R. Turner
`ChairsiEditors
`
`21—23 September 1992
`San lose, California
`
`Sponsored and Published by
`SPIE—-The International Society for Optical Engineering
`
`.F i
`
`-
`'
`-‘.
`_'
`is. to»?
`
`\
`-.-
`_'i-: -- r-
`
`
`
`Volume 1803
`
`SPIE (The Society of Photo-Optical Instrumentation Engineers} is a nonprofit society dedicated to the
`advancement of optical and o toelectronic applied science and technology.
`tum“ F.
`lift-itiin [SE-WAN
`motor; or E3~t€itli§2i we
`Kim-titan; or WI3CON$£H
`. mason, m 537%
`
`Page 4 of 14
`——_———‘_————'m
`
`EXHIBIT A
`
`Page 4 of 14
`
`
`
`EXHIBIT A
`
`
`
`The papers appearing in this book comprise the proceedings of the meeting mentioned on
`the cover and title page. They reflect the authors’ opinions and are published as presented
`and without change,
`in the interests of timely dissemination. Their inclusion in this
`pubiication does not necessarily constitute endorsement by the editors or by SPIE.
`
`Please use the following format to cite material from this book:
`Authorts), "Title of paper," in Advanced Techniques for integrated Circuit Processing ti,
`lames Bondur, Gary Castleman, Lloyd R. Harriott, Terry R. Turner, Editors, Proc.5PlE1803,
`page numbers (1993).
`
`Library of Congress Catalog Card No. 92-62653
`ISBN 0-8194-1001—2
`
`Published by
`SPIE—The International Society for Optical Engineering
`P.O.Box10, Bellingham, Washington 98227—0010 USA
`Telephone 206(676-3290 (Pacilic Time) ' Fax 206i647-1445
`
`Copyright @1993, The Society of Photo-Optical Instrumentation Engineers.
`
`Copying of material in this book for internal or personal use, or for the internal or personal
`use of specific Clients, beyond the fair use provisions granted by the US. Copyright Law is
`authorized by SPlE subject to paymentofcopying fees. The Transactional Reporting Servico
`base fee for this volume is $4.00 per article (or portiCIn thereof), which should be paid
`directly to the Copyright Clearance Center tCCCl, 2? Congress Street, Salem, MA 01970.
`Other copying for republication, resale, advertising or promotion, or any form of systematic
`or multiple reproduction ofany material in this book is prohibited except with permission
`in writing from the publisher. The CCC lee code is 0-8194—1001-2/938400
`
`Printed in the United States ofAmerica.
`
`Page 5 of 14
`
`
`EXHIBIT A
`
`Page 5 of 14
`
`
`
`EXHIBIT A
`
`A Closed-Loop Temperature Control System
`for a Low—Temperature Etch Chuck
`
`D.R. Wright, W.D. Clark, D.C. Hartman, U.C. Sridharan', SEMATECH, Austin, TX;
`M. Kent. R. Kerns. GS/DRYTEK. Wilmington, MA.
`
`TNOW at HEWLETT—PACKARD, Palo Alto, CA.
`
`ABSTRACT
`
`A closed-loop temperature control system has been developed for use in a low—
`temperature (435°C) plasma etch system.
`The system employs an optical
`fluorescence probe on the chuck (a second probe monitors the wafer temperature as
`well) to provide feedback to the heating element on the input line of the chuck closed—
`Ioop coolant fluid. A simple proportional-integraI-derivative (PID) controller with a
`learn mode controls the rate of current pulses applied to the heater.
`Innovations
`include the direct measurement of chuck temperature for the control signal, and the
`coupling of large cooling and heating capacities in close proximity to the chuck along
`with a fast fluid flow to guarantee quick response.
`
`It provides
`The system has been tested in prolonged etch runs of many wafers.
`reliable, tight temperature control (30 as low as O.6°Cl. This level of control is
`significantly tighter than could be achieved by merely monitoring chiller bath
`temperatures.
`
`1.
`
`INTRODUCTION
`
`As semiconductor features become smaller and process requirements become
`stricter, advanced plasma etch systems require tighter control over their process
`factors. A recent project at SEMATECH worked to develop an etch system that
`would provide tight control of wafer temperature for low-temperature etch
`applications.
`
`This paper discusses the hardware for both the sensors and control systems, as
`well as results of the temperature stability, over various extended runs of hundreds
`of wafers.
`
`2. SUPPORTING HARDWARE
`
`2.1
`
`Fiber optic temperature probe
`
`The fluoroptic thermometric technique developed by Luxtron uses the
`photoluminescent response of a magnesium fluorogermanate phosphor to blue light
`pulses transmitted down a fiber optic cable probe. The rate of decay of the
`fluorescence is measured and correlated to temperature. Two types of fluoroptic
`
`0-8l94-1rgg;_2;93;$4_00
`Page 6 of 14
`
`cm: mm: mm r-mpi r an
`
`EXHIBIT A
`
`Page 6 of 14
`
`
`
`EXHIBIT A
`
`probes are available. The first type l"remote" or non-contacting) uses a phosphor
`dye painted on the sample and receives the data into the fiber from a distance.
`The second type ("contact") uses the phosphor in an encapsulation at the end of
`the fiber. Surrounded by a protective coating, this probe is used to make physical
`and thermal contact with the sample. For the application investigated during the
`project, either type could have been used for the electrode probe. The etch
`system used in the project had two chambers, each with separate "contact"
`probes for monitoring electrode temperature and wafer temperature.
`
`The electrode temperature was monitored to determine the stability of the cooling
`system. The wafer temperature was used to determine the interaction of the etch
`process and the cooling system.
`
`
`
`2.2
`
`Chiller systems
`
`Two different cooling systems were used in the tool. For the -70°C chamber, a
`standard bath-type chiller was chosen. This style of chiller controls the
`temperature of a bath through which a heat transfer fluid circulates on its way to
`the electrode (some 5 to 10 meters away).
`
`For the 435°C chamber, a system from Polycold was chosen. This cryo—cooler
`was unique in two ways. First, the refrigerant (a mixture of Freons and argon) was
`circulated through the electrode. This afforded a higher heat removal efficiency
`than circulating a heat transfer fluid between a refrigerated bath and the electrode.
`Second, there was no built-in feedback system for temperature control. These
`systems are normally run at “maximum output" for high-vacuum cold-trap
`applications, with the temperature controlled by the composition of the refrigerant
`mixture. This made it necessary to add a separate system for controlling the
`
`electrode temperature.
`
`3. HEATER/CONTROLLER DESIGN
`
`The throttling approach to temperature control consisted of a valved coolant path
`that bypassed the chuck, allowing some of the cooling fluid to be diverted away
`from the chuck in order to lower the effective cooling power of the Polycold
`system. This approach failed for three main reasons:
`
`O
`
`0
`
`0
`
`Large valves that work reliably at -1 50°C are prohibitively expensive.
`
`The chuck cooling capacity was lowered (since most of the coolant would
`be bypassed).
`
`The two~phase nature of the refrigerant meant different mixtures of
`constituents flowed in the main and bypass lines, also lowering cooling
`
`efficiency.
`
`322J’5P-‘E Vol. 1303(1'992)
`Page 7 of 14
`
`EXHIBIT A
`
`Page 7 of 14
`
`
`
`EXHIBIT A
`
`The method chosen to provide the Polycold-chilled electrode with temperature
`control in the Drytek pre-production prototype low-temperature etch system was
`by heating the cryogenic fluid in the supply line and controlling the heater power to
`maintain the desired electrode temperature. The Polycold cooling power that must
`be overcome by the heater depends on the fluid delivery temperature in a nonlinear
`manner.
`It was verified that the amount of heating power required to be
`transferred to the Polycold fluid would be within the capability of the unit and
`would not pose any difficulty for its normal operation.
`
`The heater must be insulated to prevent water-ice condensation on cryogenic
`surfaces. Enclosing the entire device in a vacuum envelope would be the preferred
`method because it also provides mechanical protection for the electrical leads to
`the heaters. The use of thermal insulation would be acceptable provided it is
`capable of cryogenic operation and is compatible with the equipment installation.
`
`In the first heater design, a brass block containing cartridge heaters was brazed to
`a straight stainless steel tube which carried the refrigerant inside a cylindrical
`vacuum enclosure.
`
`The following problems were encountered with the first design:
`
`0
`
`-
`
`0
`
`The stainless steel tube had a very low thermal conductivity. This low
`conductivity was compounded by the presence of the brazed connection to
`the heater block.
`
`The Polycold fluid moves at a velocity of several meters per second, so that
`the contact time inside the 1—inch heater was only 2 to 10 msec.
`
`"Channelling flow" occurred inside the stainless steel tube because the
`Polycold uses two~phase flow, consisting of liquid droplets entrained in a
`carrier gas. As illustrated in Figure 1, expansion of the gas as the liquid
`droplets vaporized caused a laminar gas barrier to form that impeded heat
`transfer, prevented succeeding droplets from contacting the wall,
`"channelled" them into the center of the fluid stream, and prevented
`turbulent mixing of the two-phase fluid stream.
`
`These effects combined to give the first heater design very poor performance. No
`more than 6 to 8 degrees Centigrade (C°i of temperature rise could be obtained at
`the electrode, even with the brass block at 300°C.
`
`The heater system was redesigned to address the limitations discovered in the first
`heater design. The control principle of the second design is illustrated in Figure 2.
`in this case, the process temperature to be controlled was the same as the
`feedback signal to the heater controller. The electrode temperature was measured
`by the Luxtron probe. The analog output from the Luxtron controller, which was
`proportional to the electrode temperature, was used as feedback to a three-term
`
`Page 8 of 14
`Ill.‘h-___—_———_.—_u————
`
`(DIE Unl
`
`ton:- {Inn-1); 3'13
`
`EXHIBIT A
`
`Page 8 of 14
`
`
`
`EXHIBIT A
`
`Proportional-lntegraI-Derivative (PID) process controller with auto-tune capability
`that provided time-proportioned power to the heater via a solid state relay. Direct
`control of the electrode temperature could be maintained with optimal transient
`response over the widest possible range of operating conditions.
`
`The heater design in Figure 3 was chosen to provide direct contact of the Polycoid
`fluid with a heater material (brass) of high thermal conductivity, and to provide a
`flow path that produced turbulence in the Polycoid fluid (avoiding "channelling
`flow"). Calculations showed that 600 W of heater power would be required to
`raise the Polycoid fluid temperature from -130°C to -80°C. Space was provided
`for up to 2400 W of heater capacity to ensure that the time-proportioning
`controller could be operated within its control band. The number of heaters
`installed or connected could be varied, providing a simple way to adjust the
`controlled range of heater power. The heater was mounted at atmospheric
`pressure with self-adhesive thermal insulating tape applied to prevent
`condensation. A thermocouple was provided to monitor heater temperature.
`
`The following results were obtained with this design:
`
`A maximum electrode temperature rise of over 60°C was observed.
`
`The system provided rapid transient response and stable operation over the
`range from 430°C to -80°C.
`
`The heater thermocouple indicated that the heater was maintained at
`cryogenic temperature very near the electrode temperature. This fact
`confirms the excellent heat transfer characteristics of this design.
`
`The system is capable of controlling to i1°C.
`
`The system worked very reliably throughout its installation at SEMATECH.
`
`4. OPERATIONAL TESTS
`
`4.1
`
`Hardware acceptance test
`
`As part of the hardware acceptance test prior to the shipment of the tool to
`SEMATECH, a test using a total of 550 RF (plasma) cycles was performed to
`monitor the thermal stability of the cold electrodes. Each wafer was passed from
`the cassette, via the flatfinder, to chamber 2 (oxide etch), which was held at -
`30°C by the bath—type chiller circulating methanol.
`in chamber 2, the wafer
`received five FiF cycles of 20-second duration, separated by 20 seconds. The
`recipe used was a standard oxide etch CzFe (hexafiuoroethane or Freon-116)
`chemistry with 600 W of power all to the bottom electrode. After processing in
`chamber 2, each wafer then passed into chamber 3 (poly etch), which was
`maintained at 405°C by the Polycoid with the heater and controller discussed
`
`3’13
`
`{SPi'E VOL 1
`age 9 of iii-3 U992}
`
`EXHIBIT A
`
`Page 9 of 14
`
`
`
`EXHIBIT A
`
`In chamber 3 each wafer received six RF cycles of 20-second duration,
`previously.
`separated by 20 seconds. The recipe was the SFBIargon poly etch with 400 W of
`power, almost all to the top electrode. Fifty wafers (25 in each of two cassettes)
`were processed for a grand total of 550 plasma cycles.
`
`Using the parallel output (R8232) port of the Luxtron controller, a personal
`computer recorded the temperatures of both electrodes and both wafers as well as
`flags indicating whether the plasma was on in each chamber. These data were
`captured to disk and later analyzed using a spreadsheet program.
`
`Figure 4 shows a plot of the continuously sampled temperature of both wafer and
`electrode for six plasma cycles (one water) in chamber 3 (poly). Figure 5 shows a
`plot of the continuously sampled temperature of both wafer and electrode for five
`plasma cycles (one wafer) in chamber 2 (oxide). At this scale the exponential
`behaviors of both the heating and cooling of the wafer are apparent. Figure 6 then
`shows a more long-term timeline, showing stability over several hours.
`
`Table A summarizes all of the electrode temperature data taken during the plasma
`hardware acceptance test.
`In the poly chamber, there was a standard deviation
`(1a) of 0.21 °C for the electrode while in the oxide chamber there was a standard
`
`deviation (1a) of 078°C for the electrode. The electrode data were taken from
`
`the entire test (with or without a wafer present).
`
`Table A: Summary of Hardware Acceptance Test Results
`— Pow Chamber
`Oxide Chamber
`
`078°C
`
`Number of Data Points
`
`Standard Deviation
`
`405.83%
`
`0.21 °C
`
`1648
`
`-so.79°c
`
`The results show a highly repeatable temperature control in both chambers. Both
`the bath-type chiller, using its internal feedback control, and the Polycold chiller,
`with the external heater controller, provided adequate cooling and repeatable
`temperatures Over the entire test.
`
`4.2 Marathon
`
`Following the hardware acceptance, the low-temperature etch tool was installed at
`SEMATECH. After the optimization of the etch process was completed, an
`extended test was performed on the Polycold/electrode system. Over several days
`of 24 hour-per-day operation, more than 1200 wafers were processed through the
`tool. As before, computer files were maintained of the wafer and electrode
`temperatures at roughly five-second intervals. At the completion of the marathon,
`
`30,165 measurements of the electrode temperature had been recorded. The
`
`Page 10 of 14
`
`CDJL‘ U...) 1nn1 (49 1n! 1-1.—
`
`EXHIBIT A
`
`Page 10 of 14
`
`
`
`EXHIBIT A
`
`process that was used in the marathon was different from the one used in the
`hardware acceptance test. The etch process was performed in two parts, with an
`initiation step and a main etch step. Each wafer received approximately one
`minute of plasma exposure time. The electrode temperature was set to 420°C.
`
`The results are shown in Table B. The control of the chuck temperature was not
`quite as tight as that of the hardware acceptance test. Some reasons include the
`lower base temperature, and a different etch process (with slightly higher heat load
`into the wafer while the plasma was on).
`
`Table B: Summary of Marathon Results
`
`_ PolisiiiconChambe.
`
`Number of Data Points
`
`30165
`
`420mm
`
`
`
`Standard Deviation
`
`0.5200
`
`5. CONCLUSIONS
`
`A closed-loop temperature control system has been developed for use in a low-
`temperature (435°C) plasma etch system. The system employs an optical
`fluorescence probe on the chuck to provide feedback to the heating element on the
`input line of the chuck closed-loop coolant fluid. A simple proportional-integral-
`derivative (PID) controller with 3 learn mode controls the rate of current pulses
`applied to the heater.
`
`Unlike the indirect control signal of the {remote} bath temperature, the system uses
`the direct measurement of chuck temperature for the control signal. The use of
`large cooling and heating capacities in close proximity to the chuck along with a
`fast fluid flow guarantee quick response. Careful design insures turbulence in the
`flow to guarantee good heat transport between the walls and the fluid.
`
`it provides
`The system has been tested in prolonged etch runs of many wafers.
`reliable, tight temperature control (30 as low as 06°C}. This level of control is
`significantly tighter than could be achieved by merely monitoring chiller bath
`temperatures.
`
`6. ACKNOWLEDGEMENTS
`
`The authors would like to thank Paul Grosshart for his excellent data transfer
`
`program, and Masoud Mayer for his help on the heater design and fabrication.
`This work was performed as part of a joint development project between Drytek
`and SEMATECH, a consortium of twelve semiconductor manufacturers and the
`
`federal government (DARPA).
`
`326K519“? Vol. 1803(1992}
`
`Page 11 of 14
`
`EXHIBIT A
`
`Page 11 of 14
`
`
`
`EXHIBIT A
`
`VALL [IF STMNLESS STEEL TUBE
`
`— ORUPLET IN CDH'IACT
`I«I'IITH URLL
`
`
`A/O/ /
` FDRMATIEIN [IF
`
`VRPUR BARRIER
`AT TUBE SURFACE
`
`
`
` GAS EXPQNDING ARUUND
`
`CHANELLING FLDV
`
`VAPDRIZING DREIF’LE'I'
`
`FLUID DRDPLETS
`ENTRAINED IN
`CARRIER GAS
`
`‘—
`DIRECTIDN [Ir FLEI‘mf
`
`Flgura 1
`Two-Phage Refrlgerent Flow In the Polycold Llne Heater
`
`LUXTREIN FIBER _“"'-..‘_“r_-\
`-.|—-
`
`
`‘ a "'
`LUXTRDN
`DP‘FIC CABLE
`
`
`
`SEMnlECH
`_,
`LEIMI' TEMPERATURE
`
`E1CH “JUL
`
`
`CHnHBER 3
`[LHUCK
`
`HH—
`
`ANALIJG L'lUTF’UI SIGNAL
`F’REIPEIR'IIEINAL TI] CHUCK
`TEMPERATURE
`
`
`
`RE'IURN
`_...
`
`1" [IL YE DL. U
`i.—
`
`
`SUPPL ‘I’
`
`
`|
`—-4—l— 110 VAC
`
`
`_‘
`_— \
`"I"
`+IL SI" “3 3”” -
`
`
`
`
`
`commute —-—T—1——-— - u \ r’
`RELAY
`
`
`\— CDNTR‘DL SIGNAL
`FUR SOLID STnTE RELM’
`
`\-H['ATIR‘ 91mm.
`
`Figure 2
`Schematic of Heater Controller {Second Design!
`
`Page 12 of 14
`
`rrnr “2.! 1on3 {€002} 11' 3'17
`
`EXHIBIT A
`
`Page 12 of 14
`
`
`
`EXHIBIT A
`
`ECG!”le 1mm PUTS TD
`CMI‘SE 1mm AND HIGH! mm
`RATE \flTH TIE um INTER}!!! V“:
`
`v ‘
`
`v ,.,‘.-_.,'.,‘./v/ .‘1' ,-.'.'u -.
`
`.
`
`"/10in '1':-","/.‘//Z//‘/A-;'7f7A-jv'l'1‘J/I.
`
`9-24” VGTTS RAH:
`
`Figure 3
`Heater Diagram {Second Design]
`
`20” :5!
`
`
`—|
`I
`l
`20:11:“
`20:"!!!
`ZONE“
`
`l
`20:13:”
`
`
`
`. .00... 90 ... .o .099.
`O
`O
`O
`0
`g
`0
`Mk 'I'q
`
`.000
`
`o
`
`c.°°oo’ooo°9000 o.
`9
`
`.IQ‘IOIO
`
`h
`
`-I|IZ
`
`- lo!
`
`405
`
`due
`
`‘ ‘07
`
`“In!
`
`4:09
`
`“HO
`
`Il- (hm—:30!
`
`Figure 4
`Poly Etch Chuck and Wafer Temperature for 6 HF Cycles
`
`3281’SP1E vw. 1303 (1992;
`Page 13 of 14
`
`EXHIBIT A
`
`Page 13 of 14
`
`
`
`
`
`N a
`
`I $5
`
`N I l 2 x fl
`
`zu : lI a Il
`
`n n u I u
`
`u zn x a
`
`n n Is I l I
`
`n Iu I It.
`
`EXHIBIT A
`
`
`
`
`
` 18: :1
`
`_’.3U!
`
`n
`
`
`?E:WWWMHMNWWWWPMMVWWMMMWMWW
`
`
`-'Ifl? --
`
`'108 +
`
`.199 _.
`
`
`
`EXHIBIT A
`
`Page 14 of 14
`
`