`
`v7.0.0 (2005-09)
`
`Technical Re-porf
`
`Digital cellular telecommunications system (Phase 2+);
`Universal Mobile Telecommunications System (UMTS);
`Vocabulary for 3GPP Specifications
`(3GPP TR 21.905 version 7.0.0 Release 7)
`
`x
`
`5;-"-_,
`
`[$3
`
`1*!
`
`G S I-I I
`.
`.
`
`GLOBAL SYSTEM FOR
`
`MOBILE COi\vl|\rl[}h'l(T,~\Tl().!5iS
`
`I
`
`®
`
`ZTE/SAMSUNG 1035-0001
`
`
`
`3GPP TR 21.905 Version 7.0.0 Release 7
`
`ETSI TR 121 905 V7.0.D (2005-09}
`
`Reference
`RTRETSGS-01219D5v70D
`
`Keywords
`GSM. UMTS
`
`E TS!
`
`650 Route des Luoioles
`F—0892‘l Sophia Antipolis Cedex — FRANCE
`
`Tel..‘ +33 4 92 94 42 00 Fax‘. +33 4 93 65 47 16
`
`Slret N‘ 343 523 562 0001? — NAF 7'42 C
`Association a but non lucratif enregistree a la
`Sous—Pretecture de Grease (06) N" 'r'B03l"8-B
`
`Important notice
`
`Individual copies of the present document can be downloaded from:
`httg:i!vvww_etsi.org
`
`The present document may be made available in more than one electronic version or in print. In any case of existing or
`perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
`In case of dispute. the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
`within ETSI Secretariat.
`
`Users of the present document should be aware that the document may be subject to revision or change of status.
`lnfonnation on the current status of this and other ETSI documents is available at
`httgalrgortal.etsi.orgftbrstatuslstatus.asg
`
`If you find errors in the present document, please send your comment to one of the following services:
`httgzirgortal.etsi.orgrchaircorrETSl suggort.asp_
`
`Copyright Notification
`
`No part may be reproduced except as authorized by written permission.
`The copyright and the foregoing restriction extend to reproduction in all media.
`
`(9 European Telecommunications Standards Institute 2005.
`All rights reserved.
`
`oecri”, PLUGTESTST” and ur.r1's"“‘ are Trade Marks of ETSI registered for the benefit of its Members.
`TIPHONT” and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
`SGPPT” is a Trade Mark of ETSI registered for the benefit of its Members and of the SGPP Organizational Partners.
`
`ZTE/SAMSUNG 1035-0002
`
`
`
`3GPP TR 21.905 version 7.0.0 Release 7
`
`ETSI TR 121 905 V7.0.0 (2005-09}
`
`Intellectual Property Rights
`
`[PR5 essential or potentially essential to the present document may have been declared to ETSI. The information
`pertaining to these essential lPRs, ifany. is publicly available for ETSI members and non-members. and can be found
`in ETSI SR 000 314: "!m'eHecmai Proper-ry Rights (IPRJ): Essential. orpotentfaliy Essermaf. IPRS notgfied to ETSI in
`respect ofETSI standards". which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
`server (hlt
`:/In chat
`.etsi.oror’Il’Rf|1oI11c.as . ).
`
`Pursuant to the ETSI IPR Policy, no investigation, including [PR searches, has been carried out by ETSI. No guarantee
`can be given as to the existence of other lPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
`server} which are. or may be. or may become. essential to the present document.
`
`Foreword
`
`This Technical Report (TR) has been produced by ETSI 3rd Generation Partnership Project (SGPP).
`
`The present document may refer to technical specifications or reports using their 3GPP identities. UMTS identities or
`GSM identities. These should be interpreted as being references to the corresponding ETSI deliverablcs.
`
`The cross reference between GSM. UMTS. 3GPP and ETSI identities can be found under
`hll . :H\tc11a
`.ctsi.oi'n’ke\'fL ueJ'\-'form.as
`.
`
`ZTE/SAMSUNG 1035-0003
`
`
`
`3GPP TR 21.905 version 7.0.0 Reiease 7
`
`ETSI TR 121 905 W.0.0 (2005-09)
`
`Contents
`
`lntellectuai Property
`
`Scope.........
`References
`
`Terms and definitions.
`
`9
`
`Elobolqbxbxizxbwuubaw
`
`1
`
`2 30
`
`-ABCDEFGHIJKLM OP Q S
`
`N
`
`R TUV XYZ 40ABCDEFGHIJ KLM N0P QR
`
`W
`
`Abbreviations
`
`9
`
`ZTE/SAMSUNG 1035-0004
`
`
`
`SGPP TR 21.905 version 7.0.0 Release 7
`
`ETSI TR 121 905 V7.0.0 (2005-09}
`
`........................................................................................................................................................................ ..46
`.... ..48
`
`STUVW X YZ 5 A
`
`History
`
`nnex A (informative):
`
`Change history
`
`ZTE/SAMSUNG 1035-0005
`
`
`
`3GPP TR 21.905 version 7.0.0 Release ?
`
`ETSI TR 121 905 V7.Cl.0 [2005-09}
`
`Foreword
`
`This Technical Specification has been produced by the 3” Generation Partnership Project (3GPP}.
`
`The contents ofthe present document are subject to continuing work within the TSG and may change following formal
`TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
`identifying change of release date and an increase in version number as follows:
`
`Version x.y.z
`
`where:
`
`x
`
`the first digit:
`
`1
`
`presented to TSG for information;
`
`2 presented to TSG for approval;
`
`3
`
`or greater indicates TSG approved document under change control.
`
`the second digit is incremented for all changes of substance, i.e. technical enhancements. corrections.
`updates, etc.
`
`the third digit is incremented when editorial only changes have been incorporated in the document.
`
`ZTE/SAMSUNG 1035-0006
`
`
`
`3GPP TR 21.905 version ?.l'.|.lJ Release 7:’
`
`ETSI TR 121 905 V7.0.0 (2005-09)
`
`1
`
`Scope
`
`The purpose ofthis report is to identify specialist technical terms used within the 3GPP project for the purposes of
`specifying service requirements. The motivations for this are:
`
`- To ensure that editors use terminology that is consistent across specifications.
`
`-
`
`—
`
`To provide a reader with convenient reference for technical terms that are used across multiple documents.
`
`To prevent inconsistent use of terminology across documents.
`
`This document is a collection of terms, definitions and abbreviations related to the baseline documents defining 3GPP
`objectives and systems framework. This document provides a tool for further work on BGPP technical documentation
`and facilitates their understanding.
`
`The terms. definitions and abbreviations as given in this document are either imported from existing documentation
`(ETSI, [TU or elsewhere} or newly created by 3GPP experts whenever the need for precise vocabulary was identified.
`
`2
`
`References
`
`The following documents contain provisions which, through reference in this text. constitute provisions ofthe present
`document.
`
`- References are either specific (identified by date of publication, edition number. version number. etc.) or
`non-specific.
`
`For a Specific reference. subsequent revisions do not apply.
`
`For a non-specific reference, the latest version applies. In the case ofa reference to a 3GPP document {including
`a GSM document), a non-specific reference implicitly refers to the latest version of that document in the some
`Release as the present document.
`
`Void
`
`TS 25.990: "Technical Specification Group (T50) RAN; Vocabulary “.
`
`‘The Path towa.rcls UMTS - Technologies for the information Society’ — Report #2. UMTS Forum.
`
`3
`
`Terms and definitions
`
`0-9
`
`1.8V technology Smart Card: A Smart Card operating at l.8V :: [(1% and 3V t |0%.
`
`1.8V technology Terminal: A terminal operating the Smart Card - Terminal interface at l.8V :: l0% and 3V :: 10%.
`
`3GPP Generic User Profile (CUP): The 3GPP Generic User Profile is the collection ofuser related data which affects
`the way in which an individual user experiences services and which may be accessed in a standardised manner.
`
`3GPP system: the telecommunication system standardised by the 3GPP consisting of a core network and a radio access
`network that may be either GERAN or UTRAN, or both.
`
`3GPP System core network: refers in this specification to an evolved GSM core network infrastructure.
`
`3GPP System coverage: See coverage area.
`
`SGPP System IC Card: An IC card (or 'smartcard‘} of defined electromechanical specification which contains at least
`one USIM.
`
`ZTE/SAMSUNG 1035-0007
`
`
`
`3GPP TR 21.905 version T.0.‘J Release T
`
`ETSI TR 121 905 V?.0.lJ [2005-09}
`
`3GPP System mobile termination: part of the SGPP System Mobile Station which provides fimctions specific to the
`management ofthe radio interface (Um).
`
`3GPP-WLAN Interworking: Used to generically refer to interworking between the SGPP system and the WLAN
`family of standards.
`
`3V technology Smart Card: A Smart Card operating at 3Vi 10% and SV t 10%.
`
`3V technology Terminal: A terminal operating the Smart Card - Terminal interface at 3V-:i: 10% and 5V ‘J: 10%.
`
`A A
`
`fGb mode: mode of operation of me MS when connected to the Core Network via GERAN and the A andfor Gb
`interfaces.
`
`Acceptable Cell: A cell that the UE may camp onto make emergency calls. It must satisfy certain conditions.
`
`Access conditions: A set of security attributes associated with a file.
`
`Access deiay: The value of elapsed time between an access request and a Sl.lCC6SSI'l.1l access (source: ITU-T X. I40).
`
`Access Stratum SDU (Service Data Unit): Unit of data transferred over the access stratum SAP (Service Access
`Point) in the Core Network or in the User Equipment.
`
`Access protocol: A defined set of procedures that is adopted at an interface at a specified reference point between a
`user and a network to enable the user to employ the services andfor facilities of that network (source: ITU-T l.l 12).
`
`Accounting: The process of apportioning charges between the Home Environment, Serving Network and User.
`
`Accuracy: A performance criterion that describes the degree of correctness with which a function is performed. (The
`fimction may or may not be performed with the desired speed.) (source: [TU-T 1.350).
`
`Active communication: at UF. is in active communication when it has a CS connection established. For PS active
`communication is defined by the existence of one or more Activated PDP contexts. Either one or both ofthe mentioned
`active communications may occur in the UE.
`
`Active Set: Set ofradio links simultaneously involved in a specific communication service between an UE and a
`UTRAN access point.
`
`Adjacent Channel Leakage power Ratio {ACLR): The ratio of the average power centered on the assigned channel
`frequency to the average power centered on an adjacent channel frequency. In both cases the average power is measured
`with a filter that has Root Raised Cosine (RRC) filter response with roll-offot = 0.22 and a bandwidth equal to the chip
`rate.
`
`Air Interface User Rate: The user rate between Mobile Termination and IWF. For T services it is the maximum
`possible AIUR not including padding. For NT services it is the maximum possible AIUR.
`
`ALCAP: Generic name for the transport signalling protocols used to set-up and tear-down transport bearers.
`
`Allowable PLMN: A PLMN which is not in the list offorbidden PLMN in the UE.
`
`Applet: A small program that is intended not to be run on its own, but rather to be embedded inside another application
`
`Application: an application is 3. service enabler deployed by service providers. manufacturers or users. Individual
`applications will often be enablers for :1 wide range of services. (UMTS Forum report #2) [3]
`
`Applications 1' Clients: These are services, which are designed using service capability features.
`
`Application Dedicated File (ADF): an application DF is the entry point to an application on the UICC.
`
`Application Interface: Standardiscd Interface used by applicationfclients to access service capability features.
`
`Application protocol: The set of procedures required by the application.
`
`ASCI Generic name to identify the services VGCS, VBS and eMLPP.
`
`ZTE/SAMSUNG 1035-0008
`
`
`
`3GPP TR 21.905 version 7.0.0 Release ?
`
`ETSI TR 121 905 V?.0.D [2005-O9)
`
`Authentication: A property by which the correct identity of an entity or party is established with a required assurance.
`The party being authenticated could be a user, subscriber, home environment or serving network.
`
`Available PLMN: A PLMN where the UE has found a cell that satisfies certain conditions.
`
`Average power: The thermal power as measured dirough a root raised cosine filter with roll-off ct. = 0.22 and a
`bandwidth equal to the chip rate of the radio access mode. The period of measurement shall be one power control group
`(timeslot) unless otherwise stated.
`
`B B
`
`ase Station: A base station is a network element in radio access network responsible for radio transmission and
`reception in one or more cells to or from the user equipment. A base station can have an integrated antenna or be
`connected to an antenna by feeder cables. in UTRAN it terminates the Int, interface towards the RNC. ln GERAN it
`terminates the Abis interface towards the BSC.
`
`Baseline capabilities: Capabilities that are required for a service-less UE to operate within a network. The baseline
`capabilities for a UE include the capabilities to search for, synchronise with and register (with authentication) to a
`network. The negotiation ofthc UE and the network capabilities, as well as the maintenance and termination of the
`registration are also part ofthe required baseline capabilities.
`
`Base Station Controller: This equipment in the BSS is in charge of controlling the use and the integrity of the radio
`resources.
`
`Base Station Subsystem: Either a full network or only the access part of a GERAN offering the allocation, release and
`management ofspecific radio resources to establish means of connection between an MS and the GERAN.
`A Base Station Subsystem is responsible for the resources and transmissionfreception in a set of cells.
`
`Baseline Implementation Capabilities: Set of Implementation capabilities, in each technical domain, required to
`enable a UE to support the required Baseline capabilities.
`
`Basic OR Basic Optimal Routeing
`
`Basic telecommunication service: This term is used as a common reference to both bearer services and teleservices.
`
`Bearer: A information transmission path of defined capacity, delay and bit error rate, etc.
`
`Bearer capability: A transmission fimction which the UE requests to the network.
`
`Bearer independent protocol: (UICC) Mechanism by which the ME provides the (U)SIM applications on the UICC
`with access to the data bearers supported by the ME and the network.
`
`Bearer service: A type oftelccommunicatiori service that provides the capability of transmission of signals between
`access points.
`
`Best effort QIJS: The lowest of all Q08 traffic classes. If the guaranteed Q08 cannot be delivered, the bearer network
`delivers the QoS which can also be called best effort Q05.
`
`Best effort service: A service model which provides minimal performance guarantees, allowing an unspecified
`variance in the measured performance criteria.
`
`Billing: A fimction whereby CDRS generated by the charging function are transformed into bills requiring payment.
`
`Broadcast: A value of the service attribute "communication configuration", which denotes unidirectional distribution to
`all users (source: ITU»T l.l I3).
`
`Byte code: (UICC) A hardware machine independent representation of a primitive computer operation that serves as an
`instruction to a soltware program called an interpreter or a virtual machine that simulates the hypothetical computer"s
`central processing unit. code generated by a Java compiler and executed by the Java interpreter.
`
`ZTE/SAMSUNG 1035-0009
`
`
`
`SGPP TR 21.905 version 7.0.0 Release 7
`
`ETSI TR 121 905 V't'J.'l.l.'l (2005-D9}
`
`C C
`
`able, Connector, and Combiner Losses (Transmitter) (dB): The combined losses of all transmission system
`components between the transmitter output and the antenna input (all losses in positive dB values}.
`
`Cable, Connector, and Splitter Losses (Receiver) (dB): The combined losses of all transmission system components
`between the receiving antenna output and the receiver input.
`
`CAC (Connection Admission Control}: A set of measures taken by the network to balance between the QoS
`requirements of new connections request and the current network utilisation without affecting the grade of service of
`existingfalready established connections.
`
`Call: a logical association between several users (this could be connection oriented or connection less).
`
`Charging Data Record (CDR): A formatted collection of information about a chargeable event (e.g. time of call set-
`up, duration of the call, amount of data transferred, etc) for use in billing and accounting. For each party to be charged
`for parts of or all charges of a chargeable event a separate CDR shall be generated, i.c more than one CDR may be
`generated for a single chargeable event, eg. because of its long duration, or because more than one charged party is to
`be charged.
`
`Carnped on a cell: The UE is in idle mode and has completed the cell sclectionfrcselcction process and has chosen a
`cell. The U8 monitors system information and (in most cases) paging information. Note that the services may be
`limited, and that the PLMN may not be aware of the existence of the UE within the chosen cell.
`
`Capability Class: A piece of information which indicates general 3GPP System mobile station characteristics (e.g.
`supported radio interfaces,...) for the interest of the network.
`
`Card session: A link between the card and the external world starting with the ATR and ending with a subsequent reset
`or a deactivation of the card.
`
`CBS DRX cycle: The time interval between successive readings of BMC messages.
`
`Cell: Radio network object that can be uniquely identified by a User Equipment from a (cell) identification that is
`broadcasted over a geographical area from one UTRAN Access Point. A Cell is either FDD or TDD mode.
`
`Cell Radio Network Temporary Identifier (C-RNTI): The C-RNTI is a UE identifier allocated by a controlling
`RNC and it is unique within one cell controlled by the allocating CRNC. C-RNTI can be reallocated when 3 UE
`accesses a new cell with the cell update procedure.
`
`Cellular Text telephone Modern {CTM): A modulation and coding method intended for transmission of text in voice
`channels for the application of real time text conversation.
`
`Chargeable Event: An activity utilising telecommunications network infrastructure and related services for user to user
`communication {e.g. a single call. a data oommunication session or a short message), or for user to network
`communication (cg. service profile administration). or for inter-network communication (cg. transferring calls,
`signalling. or short messages). or for mobility [e.g. roaming or inter-system handover), which the network operator
`wants to charge for. The cost of a chargeable event may cover the cost of sending, transporting. delivery and storage.
`The cost of call related signalling may also be included.
`
`Charged Party: A user involved in a chargeable event who has to pay parts or the whole charges of the chargeable
`event, or a third party paying the charges caused by one or all users involved in the chargeable event, or a network
`operator.
`
`Charging: A function whereby information related to a chargeable event is fonnarted and transferred in order to make
`it possible to determine usage for which the charged party may be billed.
`
`Cipher key: A code used in conjunction with a security algorithm to encode and decode user andlor signalling data.
`
`Closed group: A group with a pre-defined set of members. Only defined members may participate in a closed group.
`
`Coded Composite Transport Channel: A data stream resulting from encoding and multiplexing of one or several
`transport channels.
`
`Common Channel: A Channel not dedicated to a specific UE.
`
`ZTE/SAMSUNG 1035-0010
`
`
`
`3G-PP TR 21.905 version 7.0.0 Release 7
`
`10
`
`ETSI TR 121 905 V7.lJ.lZl [2005-U9}
`
`Confidentiality: The avoidance of disclosure of information without the permission of its owner.
`
`Connected Mode: Connected mode is the state of User Equipment switched on and an RRC connection established.
`
`Connection: A communication channel between two or more end-points (e.g. terminal, server etc.).
`
`Connection mode: The type of association between two points as required by the bearer service for the transfer of
`information. A bearer service is either connection-oriented or connectionless. In a connection oriented mode, a logical
`association called connection needs to be established between the source and the destination entities before information
`can be exchanged between them. Connection oriented bearer services lifetime is the period of time between the
`establishment and the release of the connection. In a connectionless mode, no connection is established beforehand
`between the source and the destination entities; the source and destination network addresses need to be specified in
`each message. Transferred information cannot be guaranteed of ordered delivery. Connectionless bearer services
`lifetime is reduced to the transport ofone message.
`
`Conneetionless (for a bearer service): In a connectionless bearer, no connection is established beforehand between the
`source and the destination entities ; the source and destination network addresses need to be specified in each message.
`Transferred infonnation cannot be guaranteed ofordered delivery. Connectionless bearer services lifetime is reduced to
`the transport of one message.
`
`Connectionless service: A service which allows the transfer of information among service users without the need for
`end-to-end call establishment procedures (source: lTU-T l.l I3).
`
`Control channel: A logical channel that carries system control information.
`
`Controlling RNC: A role an RNC can take with respect to a specific set ofUTRAN access points. There is only one
`Controlling RNC for any UTRAN access point. The Controlling RNC has the overall control of the logical resources of
`its UTRAN access point's.
`
`Conversational service: An interactive service which provides for bi-directional communication by means of real-time
`[no store—a.nd-forward) end-to-end information transfer from user to user (source: lTU~T [.1 13).
`
`Core network: An architectural term relating to the part of 3GPP System which is independent of the connection
`technology of the terminal (cg radio. wired].
`
`Core Network Operator: Operator that offers core network services.
`
`Corporate code: Code which when combined with the network and SP codes refers to a unique Corporate. The code is
`provided in the GIDZ tile on the (U)SIM (see Annex A. l .) and is correspondingly stored on the ME.
`
`Corporate code group combination of the Corporate code and the associated SP and network codes.
`
`Corporate personalisation: Allows a corporate customer to personalise MES that he provides for his employees or
`customers use so that they can only be used with the company's own (U)SlMs.
`
`Coverage area (ofa mobile cellular system): An area where mobile cellular services are provided by that mobile
`cellular system to the level required of that system.
`
`Coverage area: Area over which a 3GP? System service is provided with the service probability above a certain
`threshold.
`
`Current directory: The latest MF or DP selected on the UICC.
`
`Current EF: The latest EF selected.
`
`Current serving cell: This is the cell on which the MS is camped.
`
`D D
`
`ata field: Obsolete term for Elementary File.
`
`Data Object: information coded as TLV objects, i.e. consisting of a Tag, a Length and a Value part.
`
`ZTE/SAMSUNG 1035-0011
`
`
`
`3GPP TR 21.905 version ?.0.0 Release 1'
`
`11
`
`ETSI TR 121 905 V7.0.‘J [2005-09)
`
`Dedicated Channel: A channel dedicated to a specific UE.
`
`De-personalisation: Is the process of deactivating the personalisation so that the ME ceases to carry out the verification
`checks.
`
`Dedicated File (DF): A file containing access conditions and. optionally. Elementary Files (EFS) or ot.l1er Dedicated
`Files (DPS).
`
`Delivered QS: Actual QoS parameter values with which the content was delivered over the lifetime of a (305 session.
`
`Demand service: A type of telecommunication service in which the communication path is established almost
`immediately, in response to a user request effected by means of user-network signalling (source: [TU-T [.112].
`
`Dependability: A performance criterion that describes the degree of certainty (or surety] with which a function is
`performed regardless of speed or accuracy, but within a given observational interval (source: ITU-T 1.350).
`
`Destination user: Entity to which calls to the General Packet Radio Service (GPRS) are directed.
`
`Directory: General term for the MF or a DF on the UICC.
`
`l_. 2, 3, 4, 5, 6. T. 8, 9, *, #, a.
`Directory Number: A string consisting of one or more of the characters from the set {0,
`b, c} associated with a nature of address indicator and number plan indicator. When using the public MMI for the
`control of supplementary services however. * and it cannot be part of any SC or St field.
`
`NOTE 1 : No such restriction on the SC and SI fields exists when using other (e.g. menu-driven) MM] for the
`control of supplementary services.
`
`NOTE 2: When using the public MM], certain limitations on the use ofone and two digit directory numbers may
`apply. The use of other MMI can remove these restrictions.
`
`NOTE 3: This definition is not intended to require the support of all these characters in the MM] itself.
`
`Distribution service: Service characterised by the unidirectional flow of information from a given point in the network
`to other (multiple) locations (source: [TU-T L113).
`
`Domain: The hi ghest-level group of physical entities. Reference points are defined between domains.
`
`Domain Specific Access Control: Access control functionality for access barring in either domain (i.e. CS domain or
`PS domain).
`
`Donor network: The subscription network from which a number is ported in the porting process. This mayor may not
`be the number range owner network.
`
`Downlink: Unidirectional radio link for the transmission of signals from a UTRAN access point to a UE. Also in
`general the direction from Network to UE.
`
`Drift RNS: The role an RNS can take with respect to a specific connection between a UE and UTRAN. An RNS that
`supports the Serving RNS with radio resources when the connection between the UTRAN and the User Equipment need
`to use cell(s] controlled by this RNS is referred to as Drift RNS.
`
`E E
`
`nterprise Systems: Information Systems that are used in the telecommunication organisation but are not directly or
`essentially related to the telecommunications aspects (Call Centre's. Fraud Detection and Prevention Systems, Invoicing
`etc).
`
`Element Manager: Provides a package ofend-user firnctions for management of a set of closely related types of
`network elements. These functions can be divided into two main categories.
`
`Element Management Functions: Set of functions for management of network elements on an individual basis. These
`are basically the same functions as supported by the corresponding local terminals.
`
`Elementary File (EF): A file containing access conditions and data and no other files on the UICC.
`
`ZTE/SAMSUNG 1035-0012
`
`
`
`3GPP TR 21.905 Version 7.0.0 Release 7
`
`12
`
`ETSI TR 121 905 V7.l.'|'.0 (2005-I19}
`
`Essential UE Requirement (Conditional): Requirement which has to be implemented under certain Service
`conditions. e.g. AMR codec in UE which supports speech service
`
`Essential UE Requirement (Unconditional): Requirement which has to be implemented in any 3G UE in order to
`exist in and communicate with 3G network (e.g. Chiprate of 3.34Mcps).
`
`Explicit Diversity Gain (:18): The effective gain achieved using diversity techniques.
`
`Extra SDU delivery probability: The ratio of total (unrequested) extra service data units (SDUs] to total service data
`units received by a destination user in a specified sample (source: [TU-T X. I40}.
`
`NOTE:
`
`the term "user information unit" has been replaced by the term "service data unit".
`
`F F
`
`ile: A named and hierarchically-classified data set on the UICC.
`
`File identifier {FlD): The 2-byte name ofa file or a directory on the UICC.
`
`Fixed Network User Rate: The user rate between IWF and the fixed network.
`
`FC (Flow Control): A set of mechanisms used to prevent the network from becoming overloaded by regulating the
`input rate transmissions.
`
`Flexible Layer One (FLO): GERAN feature that allows the channel coding ofthe layer one to be configured at call
`setup.
`
`Framework: A framework defines a set of Application Programming interface (API) classes for developing
`applications and for providing system services to those applications.
`
`Functional group: A set of functions that may be performed by a single equipment (source: ITU-T L1 12).
`
`G G
`
`eographical routing: The conversion of the PDU"-s geographical area definition. which specifies the area in which
`the PDU will be broadcast, into an equivalent radio coverage map.
`
`GERAN Radio Network Temporary Identifier (G-RNTI): G-RNTI is an MS identifier which is allocated by the
`Serving BSC and is unique within this SBSC. It is allocated for all MSS having an RRC connection. The G-RNTI is
`always reallocated when the Serving BSC for the RRC connection is changed and deallocated when the RRC
`connection is released. The Ci-RNTI is also used at RLCIMAC during contention resolution.
`
`GPRS MS: An MS capable ofGPRS services is a GPRS MS.
`
`Group: A set ofmembers allowed to participate in the group call service. The group is defined by a set of rules that
`identifies a collection of members implicitly or explicitly. These rules may associate members for the purpose of
`participating in a group call, or may associate members who do not participate in data transfer but do participate in
`management, security. control, or accounting for the group.
`
`Group call: The relationship that exists between the members of a group for the purpose of transferring data. More than
`one group call may exist in a group. A group call establishes an active group.
`
`Group call initiator: A member [or third party) authorised to initiate a group call. More than one member may initiate
`group calls.
`
`Group call participant: A member of a group participating in a particular group call at a given time.
`
`Group call server: A logical entity that provides the group call service to the members.
`
`Group call service: A PTM service in which a relationship exists between participants of the group, and in which a
`single data unit transmitted by a source participant is received by multiple destination participants; it is a one-in, many-
`out service.
`
`Grup controller: The member (or third party) responsible for the group creation and membership control.
`
`ZTE/SAMSUNG 1035-0013
`
`
`
`3GFP TR 21.905 version 7.0.0 Release 7
`
`13
`
`ETSI TR 121 905 V7.0.0 [2005-O9)
`
`GSM.-‘EDGE Radio Access Network: GERAN is a conceptual temt identifying that part of the network which consists
`of BSCs and BTSs between AIGIJ or In and Urn interfaces.
`
`GSM BSS: refers in this specification to the GSWGPRS access network.
`
`GSM core network: refers in this specification to the GSM NSS and GPRS backbone infrastructure.
`
`GSM coverage: an area where mobile cellular services are provided in accordance with GSM standards
`
`GSM session: That part of the card session dedicated to the GSM operation.
`
`Guaranteed service: A service model which provides highly reliable performance, with little or no variance in the
`measured performance criteria.
`
`H H
`
`andoff GaintLoss (dB): This is the gainfloss factor (+ or -) brought by handoff to maintain specified reliability at the
`cell boundary.
`
`Handover: The transfer of a user"s connection from one radio channel to another (can be the same or different cell).
`
`Handover: The process in which the radio access network changes the radio transmitters or radio access mode or radio
`system used to provide the bearer services. while maintaining a defined bearer service QoS.
`
`Hard Handover: Hard handover is a category of handover procedures where all the old radio links in the UE are
`abandoned before the new radio links are established.
`
`HE-VASP: Home Environment Value Added Service Provider. This is a VASP that has an agreement with the Home
`Environment to provide services. The Home Environment provides services to the user in a managed way, possibly by
`collaborating with l-iE~VASPs, but this is transparent to the user. The same service could be provided by more than one
`HE-VASP and each HE—VASP can provide more than one service.
`
`Home Environment: responsible for overall provision and control of the Personal Service Environment of its
`subscribers.
`
`Home PLMN: PLMN where the Mobile Country Code (MCC) and Mobile Network Code (MNC) ofthe PLMN
`identity are the same as the MCC and MNC ofthe {MS}.
`
`IC Card: A card holding an integrated Circuit containing subscriber, end user, authentication andlor application data
`for one or more applications.
`
`IC card SIM: Obsolete term for ID-l SIM.
`
`ICS proforma: A document, in the form of a questionnaire, which when completed for an implementation or system
`becomes an ICS.
`
`[D-000 SIM: A UICC having the form on an [D-O00 card (see [S0