`WKI
`
`Construction and performance of a 576x576 single-stage OXC
`
`Herzel Laor, Consultant
`Astarté Fiber Networks, Inc.
`2555 55"‘ St., Boulder, co 80301
`Tel; 303-443-8778
`
`herzel.laor@starswitch.com
`
`With the explosive growth in data communications, management of fiber networks becomes a crucial
`issue. Optical Cross-Connects (OXCS) are ideal for this application, if they satisfy several critical
`requirements: large fiber count, transparency (to allow future increase of bit rates), and low-loss
`performance.
`
`One practical way to create such an OXC uses a sing1e—stage, free-space design. In this design, an
`optical unit attached to each fiber creates an expanded beam, which is directed in space. A large
`number or such optical units can interconnect to form a large, transparent, low-loss OXC.
`
`OPTICAL UNIT
`
`Figure 1: Directable Beams in Space
`
`This basic free-space architecture is used in an existing commercial 72 x 72 multi-mode fiber cross-
`connect. Excellent performance has been demonstrated by these systems in the field. In this design,
`beam manipulation is performed with piezo-electric actuators, which move the fiber in two degrees
`of freedom.
`
`In the new OXC under development, MEMS mirrors are used to direct the beams rather than the
`earlier piezo devices. The mirrors were developed by Texas Instruments, Incorporated. The mirrors
`are fabricated from silicon, and have an active area that measures 3 mm x 4 mm. The mirrors are
`magnetically actuated for rotation with two degrees of freedom. The mirrors have a precision surface
`
`0-7803-5634-9/99/$l0.00©1999 IEEE
`
`481
`
`Petitioner Ciena Corp. et al.
`Exhibit 1030-1
`
`
`
`that is gold-plated, resulting in diffraction-limited performance with a 3-mm diameter beam. Each
`mirror is hermetically sealed in a ceramic carrier with a glass window. Since the mirror is directing
`the expanded beam, the lens is always on-axis, allowing the use of a simple lens.
`
`Four control LEDs surround each mirror, emitting short-wave infrared light at 880 nm. These
`control signals are used for servo control of the position of the MEMS mirrors. The LED signals are
`detected using a silicon-based detector mounted near the end of the communication fiber. A. dichroic
`bearn-splitter decouples the communication wavelength from the control wavelength; the
`communication beam is focussed on the fiber end, while the control signals arriving from the
`opposing unit are focussed on the servo detector.
`
`FIXED MIRROR
`
`”\
`
`*’
`
`SERVO DETECTOR
`
`Figure 2: Optical Unit
`
`Loss performance of 3-4 dB was measured’ for several optical units, well in line with the target
`specification of 6dB. These measurements were done at 1550 nm. The specified transmission
`window is 1260-1360 and 1500-1650 nm; at 13 10 nm the loss performance was somewhat better
`than at 1 550. The optics are being optimized to further improve performance for the 1 500-1650 nm
`window. The target for polarization-dependent loss is less than 0.5 dB; it was measured at less then
`0.4 dB. Optical improvements should reduce this figure further.
`
`Cross talk was targeted to be -50 dB (optical) below the signal level. While switching, when a beam
`scans over other units not aimed at the scarming beam, the cross talk is doubled for a very short
`while. This is because most of the cross talk originates from scattering in the optics. The doubled
`cross talk was measured at -41.6 dB. From this measurement we extrapolate -80 dB optical cross
`talk, which translates to -160 dB when measured at the electrical level.
`
`432
`
`Petitioner Ciena Corp. et al.
`Exhibit 1030-2
Accessing this document will incur an additional charge of $.
After purchase, you can access this document again without charge.
Accept $ Charge
Still Working On It
This document is taking longer than usual to download. This can happen if we need to contact the court directly to obtain the document and their servers are running slowly.
Give it another minute or two to complete, and then try the refresh button.
A few More Minutes ... Still Working
It can take up to 5 minutes for us to download a document if the court servers are running slowly.
Thank you for your continued patience.
This document could not be displayed.
We could not find this document within its docket. Please go back to the docket page and check the link. If that does not work, go back to the docket and refresh it to pull the newest information.
Your account does not support viewing this document.
You need a Paid Account to view this document. Click here to change your account type.
Your account does not support viewing this document.
Set your membership
status to view this document.
With a Docket Alarm membership, you'll
get a whole lot more, including:
- Up-to-date information for this case.
- Email alerts whenever there is an update.
- Full text search for other cases.
- Get email alerts whenever a new case matches your search.
One Moment Please
The filing “” is large (MB) and is being downloaded.
Please refresh this page in a few minutes to see if the filing has been downloaded. The filing will also be emailed to you when the download completes.
Your document is on its way!
If you do not receive the document in five minutes, contact support at support@docketalarm.com.
Sealed Document
We are unable to display this document, it may be under a court ordered seal.
If you have proper credentials to access the file, you may proceed directly to the court's system using your government issued username and password.
Access Government Site
