`
`IN THE UNITED STATES PATENT AND TRADEMARK OFFICE
`
`In re Patent of:
`U.S. Patent No.:
`Issue Date:
`Appl. Serial No.:
`Filing Date:
`Title:
`
`Hays et al.
`5,659,891
`Aug. 19, 1997
`08/480,718
`Jun. 7, 1995
`MULTICARRIER TECHNIQUES IN BANDLIMITED CHANNELS
`
`DECLARATION OF DR. APOSTOLOS K. KAKAES
`
`1.
`
`My name is Apostolos K. Kakaes of Vienna, Virginia. I understand that I am
`
`submitting a declaration offering technical opinions in connection with the above-referenced
`
`Inter Partes Review proceeding pending in the United States Patent and Trademark Office for
`
`U.S. Patent No. 5,659,891 (the “’891 patent”), and prior art references relating to its subject
`
`matter. My current curriculum vitae is attached and some highlights follow.
`
`2.
`
`I have over thirty (30) years of experience in electrical engineering and computer
`
`science and in fixed and mobile communications networks. I attended the University of Colorado
`
`from 1974 to 1980, during which, I earned a Bachelor of Science (B.S.) and a Master of Science
`
`(M.S.) in applied mathematics with a minor in electrical engineering. I attended the Polytechnic
`
`Institute of New York between 1982 and 1988, during which, I earned a Doctor of Philosophy
`
`(Ph.D.) in electrical engineering, with a thesis titled “Topological Properties and Design of
`
`Multihop Packet Radio Networks.” While pursuing the Ph.D. degree, I held a joint appointment
`
`as Special Research Fellow and Adjunct Instructor at the Polytechnic Institute of New York
`
`between 1985 and 1986.
`
`3.
`
`Between 1982 and 1987, I worked at AT&T Bell Laboratories in Holmdel, New
`
`Jersey. While at AT&T Bell Laboratories, I worked on modeling, analysis, design, and
`
`performance evaluation of voice and data networks. I developed algorithms for DNHR
`
`(Dynamic, Non-Hierarchical Routing) used in the telephone network. I also worked on analysis
`
`Page 1 of 23
`
`
`1
`
`Petitioner Samsung - SAM1003
`
`
`
`U.S. Patent No. 5,659,891
`
`of advanced data services and formulation of long term plans for development of enhanced data
`
`services and network design tools to support such services.
`
`4.
`
`I was an Assistant Professor of Electrical Engineering and Computer Science at
`
`The George Washington University (GWU), Washington, D.C., between 1987 and 1994. During
`
`my association with GWU, I taught graduate courses in the area of communication engineering,
`
`including communication theory, coding theory, voice and data networking, and mobile
`
`communications. I also received several research awards/grants, including the prestigious NSF
`
`Research Initiation Award.
`
`5.
`
`In 1988, I founded Cosmos Communications Consulting Corporation (“Cosmos”),
`
`which is a private communications engineering consulting firm specializing in mobile
`
`communications, and I have been the President of the company since the founding. Since 1994,
`
`I have worked full-time at Cosmos. At Cosmos, among various activities, I have consulted on
`
`high level technology-related issues and trends to corporate entities, governmental agencies, and
`
`international organizations, such as the United Nations. I have provided technical consultancy to
`
`engineering firms, operators, and equipment vendors on issues related to existing or evolving
`
`technologies for mobile communications, and to the investment community on issues related to
`
`both fixed and wireless communications technologies. I have served as consultant on both civil
`
`and criminal legal cases, including several patent infringement cases both at the ITC and in
`
`district court. I also participated as a technical consultant in the analysis of large patent
`
`portfolios for the purposes of due diligence, sales, and merger and acquisition activities for some
`
`of the largest companies in the mobile communications space. These projects spanned a
`
`multidimensional spectrum of technologies in both fixed and mobile communications as they
`
`have evolved over the past thirty (30) years.
`
`Page 2 of 23
`
`
`2
`
`
`
`U.S. Patent No. 5,659,891
`
`6.
`
`During my work at Cosmos, I have provided expert advice and conducted
`
`extensive training for practicing engineers in the field in diverse networking technology areas,
`
`including Wireless Local Area Networks (LAN), Metropolitan Area Networks (MAN), and
`
`Personal Area Networks (PAN) technologies, paging networks, ad hoc networks, including IEEE
`
`802.11 (Wi-Fi), IEEE 802.16 (WiMAX), HIPERLAN, Bluetooth, Near Field Communications,
`
`IrDA (Infrared Data Association). My experience includes detailed in depth analysis of cellular
`
`networks operating with any of the available access technologies as standardized in various
`
`standards, broadly known as AMPS, GSM, GPRS, EDGE (EGPRS); North American TDMA
`
`and IS-136, iDEN, IS-95, UMTS, HSPA, and LTE. I have experience in the design and
`
`implementation of voice and data networking (circuit switching as well as all the evolving all IP-
`
`based technologies), traffic engineering, RF design, Quality of Service (QoS) and resource
`
`allocation, MAC protocols, as well as in the design of core networks, both user plane and control
`
`plane.
`
`7.
`
`Over the course of my career, I have authored and co-authored some thirty (30)
`
`publications on various aspects of fixed and mobile communications, as noted in my curriculum
`
`vita. I am a member of the Institute of Electrical and Electronics Engineers (IEEE) and actively
`
`involved in the Communications Society and the Information Theory Society of IEEE. Between
`
`1991 and 1992, I served as the Secretary of IEEE Communications Society National Capital
`
`Area Chapter. Between 1992 and 1993, I was the Vice-Chair of IEEE Communications Society
`
`National Capital Area Chapter. I was the Vice-Chair of the Communication Theory Technical
`
`Committee of the Communications Society of the IEEE for the 1993-1996 term, and Treasurer of
`
`the Communication Theory Technical Committee of the Communications Society of the IEEE
`
`for the 1996-1999 term.
`
`Page 3 of 23
`
`
`3
`
`
`
`U.S. Patent No. 5,659,891
`
`8.
`
`I have served as a reviewer for the IEEE, book editors, other technical
`
`publications, and various National Science Foundation (NSF) Panels. I have organized technical
`
`sessions in technical conferences, including the IEEE International Conference on
`
`Communications (ICC) and IEEE Global Communications Conference (Globecom). I served as
`
`the Technical Program Chair for the Communication Theory Mini-Conference in 1992.
`
`9.
`
`I am familiar with the content of U.S. Patent No. 5,659,891 (the “’891 patent”).
`
`In addition, I have considered the various documents referenced in my declaration as well as
`
`additional background materials. For example, I have considered: (1) Dr. Rade Petrovic et al.,
`
`Permutation Modulation for Advanced Radio Paging, IEEE Proceedings of Southeastcon ‘93 (7
`
`Apr 1993) (“Petrovic”); (2) WIPO Publication No. 1989/008355 to Raith et al. (“Raith”); and (3)
`
`C. Alakija and S. P. Stapleton, A Mobile Base Station Phased Array Antenna, 1992 IEEE
`
`International Conference on Selected Topics in Wireless Communications at 118 (Jun. 1992)
`
`(“Alakija”). I have also reviewed the prosecution history of the ’891 patent and the claim
`
`construction orders from Mobile Telecommunications Technologies, LLC v. T-Mobile USA, Inc.,
`
`et al., Case No. 2:13-cv-00886-JRG-RSP (E.D. Tex.); Mobile Telecommunications
`
`Technologies, LLC v. Sprint Nextel Corp., et al., Case No. 2:12-cv-00832-JRG-RSP (E.D. Tex.);
`
`Mobile Telecommunications Technologies, LLC v. Leap Wireless International, Inc., et al., Case
`
`No. 2:13-cv-00885-JRG-RSP (E.D. Tex.); and Mobile Telecommunications Technologies, LLC
`
`v. Clearwire Corp., et al., Case No. 2:12-cv-00308-JRG-RSP (E.D. Tex.). I have also reviewed
`
`the January 22, 2015 Decision on Institution of Inter Partes Review of the Patent Trial and
`
`Appeal Board in Case IPR2014-01035.
`
`10.
`
`Counsel has informed me that I should consider these materials through the lens
`
`of one of ordinary skill in the art related to the ’891 patent at the time of the invention, and I have
`
`Page 4 of 23
`
`
`4
`
`
`
`U.S. Patent No. 5,659,891
`
`done so during my review of these materials. I believe one of ordinary skill as of June 7, 1995
`
`(the priority date of the ’891 patent) would have at least a B.S. degree in electrical engineering,
`
`computer science, computer engineering, or equivalent education. This person would also need
`
`to have at least two years of experience in the design and configuration of wireless paging
`
`systems, or other two-way wireless communications systems and be familiar with the operation
`
`and functionality of multicarrier transmissions. I base this on my own personal experience,
`
`extensive training that I provided for those in the industry as well as my knowledge of colleagues
`
`and other professionals at the time. With this in mind, for purposes of this analysis, references
`
`that I make to the views of a person of ordinary skill are intended to relate the views of that
`
`person as of June 7, 1995 or earlier, whether stated with respect to the present or past tense.
`
`11.
`
`Counsel has advised me that, during Inter Partes Review, claims of an expired
`
`patent (like the ’891 patent) are generally given their ordinary and customary meaning as
`
`understood by a person of ordinary skill in the art in question at the effective filing date of the
`
`patent. Counsel has also informed me that this may yield interpretations that are different from
`
`the interpretations applied during a District Court proceeding, such as the pending MTel
`
`litigation.
`
`12.
`
`I have no financial interest in either party or in the outcome of this proceeding. I
`
`am being compensated for my work as an expert on an hourly basis. My compensation is not
`
`dependent on the outcome of these proceedings or the content of my opinions.
`
`13. My findings, as explained below, are based on my study, experience, and
`
`background in the fields discussed above, informed by my education in applied mathematics and
`
`electrical engineering, and my experience in the design and analysis of fixed and mobile
`
`communications systems.
`
`Page 5 of 23
`
`
`5
`
`
`
`U.S. Patent No. 5,659,891
`
`14.
`
`This declaration is organized as follows:
`
`I.
`
`II.
`
`Brief Overview of the ’891 Patent (page 6)
`
`Petrovic and Combinations Based on Petrovic (page 7)
`
`III.
`
`Conclusion (page 18)
`
`Brief Overview of the ’891 Patent
`
`The ’891 patent is generally directed to “multicarrier techniques in bandlimited
`
`I.
`
`15.
`
`channels.” Ex. SAM1001, Title. The ’891 patent includes 5 claims, of which claims 1, 3, and 5
`
`are independent.
`
`16.
`
`The ’891 patent describes “a method for operating more than one carrier in a
`
`single mask-defined, bandlimited channel assigned to mobile paging use.” Ex. SAM1001, 1:6-8.
`
`Features of the claims are readily discernible from FIGS. 3A and 3B, which the ’891 patent
`
`describes as follows:
`
`Referring to FIG. 3A. two submasks defining two subchannels. 30a and 30b, are
`
`asymmetrically located within a single mask-defined, bandlimited channel 31, resulting
`
`in some subchannel overlap. FIG. 3B depicts two carriers, 32a and 32b, operating
`
`respectively over two asymmetrically-located subchannels, resulting in some carrier
`
`overlap. In accordance with this asymmetry, the frequency difference between the center
`
`frequency of each carrier and the nearest band edge of the mask is greater than half the
`
`frequency difference between the center frequencies of the two carriers.
`
`Ex. SAM1001, 4:25-35. An annotated version of FIG. 3B is provided below to illustrate one
`
`implementation of the claim language.
`
`Page 6 of 23
`
`
`6
`
`
`
`U.S. Patent No. 5,659,891
`
`
`
`17.
`
`The ’891 patent acknowledges the prior existence of “traditional multicarrier
`
`design[s]” in which “carriers are symmetrically located within the channel such that they are
`
`evenly spaced relative to each other and to the band edges of the primary mask defining the
`
`primary channel.” Ex. SAM1001, 2:1-12. Thus, the alleged invention of the ’891 patent is the
`
`spacing of the carriers within the channel. See Ex. SAM1001, 2:15-17, 2:26-36. As will be
`
`described in the following sections, however, the claimed positioning of carriers within a channel
`
`was well known in the art well before June 7, 1995.
`
`II.
`
`Petrovic and Combinations Based on Petrovic
`
`A.
`
`Petrovic
`
`18.
`
`Petrovic describes the authors’ “efforts to increase both bit rate and spectral
`
`efficiency in simulcast paging networks.” Ex. SAM1013, p. 1, Introduction. To accomplish this
`
`Page 7 of 23
`
`
`7
`
`
`
`U.S. Patent No. 5,659,891
`
`goal, Petrovic outlines a “multicarrier permutation modulation technique” that “can be used in
`
`simulcast networks with high power transmitters.” Ex. SAM1013, p. 1, Abstract. This type of
`
`modulation is often classified as Multicarrier Modulation (MCM). Ex. SAM1013, p. 1, Proposed
`
`Modulation Technique. The MCM technique described by Petrovic involves encoding data
`
`across eight subcarrier frequencies within a band-limited channel. See Ex. SAM1013, p. 1,
`
`Proposed Modulation Technique. “The signal spectrum at transmitter output is presented in Fig.
`
`1, and 2.” Ex. SAM1013, p. 2, Experiments.
`
`19.
`
`The proposed multicarrier permutation modulation technique includes “moving
`
`the current emission mask boundaries away from the center frequency by +/- 12.5 kHz. This
`
`would give a 35 kHz pass band in the middle of the channel and 7.5 kHz guard bands on each
`
`side for the skirts of the spectrum.” Ex. SAM1013, p. 1, Proposed Modulation Technique. To
`
`illustrate the mask boundaries of the band-limited channel, Petrovic guides the reader to “[s]ee
`
`dashed lines in Figs. 1 and 2,” which “represent[] the proposed emission mask.” Ex. SAM1013,
`
`p. 1, Proposed Modulation Technique; p. 2, Experiments. The following Annotation 1 of FIG. 1
`
`highlights the guard bands with relation to the mask boundaries.
`
`Page 8 of 23
`
`
`8
`
`
`
`U.S. Patent No. 5,659,891
`
`
`These 7.5 kHz guard bands are each only a portion of the frequency difference
`
`20.
`
`between the center frequency of the outer most of the carriers and the band edge of the mask
`
`defining the channel. Thus, the frequency difference between the center frequency of the outer
`
`most of the carriers and the band edge of the mask defining the channel is at least 7.5 kHz.
`
`21.
`
`Petrovic further describes that, “[i]n order to fully utilize the allocated spectrum,
`
`and provide fast fall-off of the spectrum in the guard band we propose eight subcarriers spaced 5
`
`kHz apart, so that there is exactly 35 kHz spacing between end subcarriers.” See Ex. SAM1013,
`
`p. 1. The following Annotation 2 of FIG. 1 highlights the spacing between the center frequency
`
`of the subcarriers described by Petrovic.
`
`Page 9 of 23
`
`
`9
`
`
`
`U.S. Patent No. 5,659,891
`
`
`Taking these teachings together, Petrovic describes a guard band of 7.5 kHz (as
`
`22.
`
`shown in Annotation 1) and a spacing between the center frequency of adjacent carriers of 5 kHz
`
`(as shown in Annotation 2). In other words, the frequency difference between the center
`
`frequency of the outer most of the carriers and the band edge of the mask defining said channel
`
`(which is greater than 7.5 kHz) is more than half the frequency difference between the center
`
`frequencies of each adjacent carrier (which is 5 kHz), as required by claim 1. Thus, Petrovic
`
`describes the feature that led to the allowance of the ’891 patent.
`
`23.
`
`In Petrovic’s modulation scheme, adjacent subcarriers partially overlap each
`
`other. The following Annotation 3 of FIG. 1 shows the hypothetical position of the eight
`
`subcarriers within the bandlimited channel, with carriers/subchannels 1, 2, 4 and 8 being ‘ON’
`
`and carrier/subchannels 3, 5, 6, and 7 being ‘OFF’.
`
`Page 10 of 23
`
`
`10
`
`
`
`U.S. Patent No. 5,659,891
`
`24. Where the value of the transmitted signal between carrier/subchannel 1 and
`
`carrier/subchannel 2 (highlighted in blue below) does not return to practical zero (highlighted as
`
`a red broken line that extends the lowest point of the mask), the carrier/subchannel 1 overlaps
`
`adjacent carrier/subchannel 2. This is illustrated in the following Annotation 4 of an excerpt of
`
`FIG. 1, which is shown side-by-side with a similarly annotated FIG. 5A of the ’891 patent to
`
`illustrate the similar type of overlap.
`
`
`
`25.
`
`Petrovic describes using a transmitter with four subtransmitters to transmit the
`
`eight subcarriers. Ex. SAM1013, p. 2, Experiments. In particular, “[e]ach transmitter has four
`
`subtransmitters capable of 4-FSK over a subset of the 8 frequencies. Outputs of the
`
`subtransmitters are combined and sent to a common antenna.” Id. Thus, each of the eight
`
`subcarriers are transmitted from the same location (i.e., the common antenna). It would have
`
`been understood by one of ordinary skill that a plurality of Petrovic’s mobile receiving units
`
`independently receive one of the plurality of transmitted subcarriers. For example, Petrovic
`
`describes that “[a] receiver . . . consists of an RF section which down converts the signal to a
`
`Page 11 of 23
`
`
`11
`
`
`
`U.S. Patent No. 5,659,891
`
`frequency band below 100 kHz, an A/D converter, a DSP processor which performs signal
`
`detection through DFT analysis, and a PC to control the operation and present results. SeeEx.
`
`SAM1013, p. 2, Experiments.
`
`26.
`
`Petrovic describes that “[e]ach transmitter has four subtransmitters capable of 4-
`
`FSK over a subset of the 8 frequencies. Outputs of the subtransmitters are combined and sent to
`
`a common antenna.” Ex. SAM1013, p. 2, Experiments. Each subtransmitter generates and
`
`modulates a signal to be transmitted. Ex. SAM1013, p. 3, Proposed Modulation Technique. A
`
`block diagram of the four “subtransmitters” described by Petrovic would be structured in a
`
`similar manner to the systems shown in either of Figures 1 and 2 of the ’891 patent, except with
`
`four data sources and modulators instead of two. Indeed, as in Figures 1 and 2 of the ’891
`
`patent, Petrovic describes that “[o]utputs of the subtransmitters are combined and sent to a
`
`common antenna [i.e., transmission source].” Ex. SAM1013, p. 2, Experiments.
`
`B.
`
`Combination of Petrovic, Raith, and Alakija
`
`27.
`
`I have been asked to consider a scenario in which the “co-locating” limitation of
`
`claim 5 requires co-locating a plurality of structurally separate transmitters. In such a scenario,
`
`Petrovic discloses a plurality of transmitters, but does not explicitly disclose co-location. Rather,
`
`under such a construction Petrovic discloses two transmitters located seven miles apart. See Ex.
`
`SAM1013, p. 2, Experiments. However, based on Petrovic in view of Raith and Alakija it would
`
`be obvious to co-locate the plurality of transmitters disclosed in Petrovic such that the plurality
`
`of carriers can be emanated from the same transmission source.
`
`28.
`
`In particular, Petrovic describes an experiment in which “[t]wo transmitters [each
`
`including four subtransmitters capable of 4-FSK over a subset of the 8 described frequencies]
`
`were installed seven miles apart and synchronized to provide a simulcast overlap area with
`
`Page 12 of 23
`
`
`12
`
`
`
`U.S. Patent No. 5,659,891
`
`approximately 35 dBpV/r signal strength.” Ex. SAM1013, p. 2, Experiments. Thus, Petrovic
`
`describes a plurality of geographically spaced transmitters, but describes them as being located
`
`seven miles apart. However, co-location of transmitters was well known in the art and the
`
`number and location of transmitters in the paging system described by Petrovic would simply be
`
`a matter of design choice that would have been obvious to one of ordinary skill in the art. In
`
`fact, the ’891 specification describes at least two potential benefits of co-located
`
`transmitters:“[b]ecause transmitter co-location does not give rise to the near-far problem to
`
`which the FCC mask requirements are directed, carrier spacings far closer than would ordinarily
`
`be allowed (e.g., 5 to 10 kHz) are achievable. Moreover, the carriers need not be symmetrically
`
`or evenly spaced within the mask defining the channel.” Ex. SAM1001 at 4:12-23. In other
`
`words, co-locating transmitters can have subcarriers (1) more closely divided (e.g., less than 5
`
`kHz) and (2) non-evenly spaced. Petrovic, however, discloses subcarriers that are evenly spaced
`
`at 5 kHz. Ex. SAM1013, p. 2, Proposed Modulation Technique. Therefore, a person having
`
`ordinary skill in the art at the time would have been motivated to co-locate transmitters so that
`
`the subcarriers described in Petrovic be more closely and/or asymmetrically placed without
`
`causing undue interference.
`
`29.
`
`For example, Figure 1 of Raith describes “the division of an area into cells and the
`
`assignation of base station transmitters to the cells in a mobile telephone system.” Ex.
`
`SAM1014, 6:1-3. For adjacent cells, Raith describes that it is common to co-locate groups of
`
`three base transmitters to service contiguous cells. See Ex. SAM1014, 6:11-13. Thus, as
`
`highlighted in the following annotation of Figure 1, “the base station transmitter BS1 for the cell
`
`C1 is co-located with the base station transmitter BS3 for the cell C3 and the base station
`
`transmitter BS5 for the cell C5.” Ex. SAM1014, 6:13-15 (emphasis added).
`
`Page 13 of 23
`
`
`13
`
`
`
`U.S. Patent No. 5,659,891
`
`
`The systems of Petrovic and Raith are similar. Raith describes a cellular digital
`
`30.
`
`mobile radio system with plural base station transmitters and a method of transmitting
`
`information in such a system. Ex. SAM1014, Title. Specifically, Raith describes:
`
`[A]t least two base station transmitters (Bma, Bmb, Bna, Bnb) at a given
`transmitting distance from each other are assigned to each of certain cells (Cm,
`Cn) within a restricted geographical area. The base station transmitters which are
`assigned to the same cell transmit digitally modulated radio signals within the
`same frequency range at least partially simultaneously to the mobile stations of
`the cell. The radio signals from different base station transmitters associated with
`
`Page 14 of 23
`
`
`14
`
`
`
`U.S. Patent No. 5,659,891
`
`the same cell are digitally modulated with the same message information to the
`mobile stations in the cell.
`Ex. SAM1014, Abstract. In other words, each individual cell described by Raith is similar to the
`
`experiment described by Petrovic, with two transmitters located a certain distance apart to
`
`simultaneously transmit the same message information to a mobile station. Raith simply
`
`describes a more complex network of cells and associated transmitters, which are used for two-
`
`way telephone communication, as opposed to one-way pager communication.
`
`31.
`
`Considering Petrovic and Raith in combination, one of ordinary skill in the art
`
`would have been motivated to expand the experimental paging system configuration described in
`
`Petrovic to include multiples adjacent paging cells/regions similar in structure illustrated in
`
`Figure 1 of Raith. In this modified configuration, multiple transmitters configured and operated
`
`as described by Petrovic would be co-located to service contiguous cells, as described by Raith.
`
`The following annotation of a portion of FIG. 1 of Raith illustrates the proposed combination.
`
`
`
`Page 15 of 23
`
`
`15
`
`
`
`U.S. Patent No. 5,659,891
`
`32.
`
`One of ordinary skill in the art would have been motivated to expand the
`
`experiment described by Petrovic in order to provide messaging services to a larger geographic
`
`area and a larger number of mobile devices (e.g., pagers).
`
`33.
`
`To the extent it is found that Petrovic in view of Raith does not explicitly describe
`
`emanating a plurality of carriers from the same transmission source, it would have been obvious
`
`to one of ordinary skill in the art to connect the plurality of co-located transmitters taught by
`
`Petrovic in view of Raith to a single antenna structure, such as the one described by Alakija, such
`
`that the plurality of carriers output by the co-located transmitters could be emanated from the
`
`same transmission source.
`
`34.
`
`In particular, Alakija describes a “mobile communications base station antenna,
`
`which utilizes a cylindrical array design.” Ex. SAM1015, Abstract. “Using a switching matrix,
`
`different subsets of antenna elements, in the array, can be excited, thus producing a narrow
`
`steerable beam.” Id. In one configuration of the cylindrical antenna, Alakija describes that,
`
`“[b]y combining a number of feed networks into a single antenna system, an antenna with
`
`multiple independently steerable beams is achieved.” Ex. SAM1015, pp. 1-2 (emphasis
`
`added). One of ordinary skill would have understood that each of the three co-located
`
`transmitters described by Petrovic in view of Raith could provide the “number of feed networks”
`
`contemplated by Alakija as inputs to the cylindrical antenna. The following annotated version of
`
`FIG. 6 of Alakija illustrates this configuration:
`
`Page 16 of 23
`
`
`16
`
`
`
`U.S. Patent No. 5,659,891
`
`
`35. Moreover, Alakija describes that the characteristics of the cylindrical antenna can
`
`be altered to cater to variable sector sizes. See Ex. SAM1015, p. 2. Examples of these different
`
`patterns that can be obtained by varying phase distribution of the cylindrical antenna are shown
`
`in FIG. 9. See Ex. SAM1015, pp. 2-3. One of ordinary skill in the art would have understood
`
`that one of the illustrated patterns would readily service the mobile cell structure described by
`
`Raith. In the following diagram, three of the independently steerable beams taught by FIG. 9 of
`
`Alakija (i.e., the red pattern that is shown in FIG. 9 and the two blue patterns that one of ordinary
`
`skill in the art would have understood could be independently steered as part of the configuration
`
`shown in FIG. 6) have been overlayed on FIG. 1 of Raith to illustrate this point.
`
`Page 17 of 23
`
`
`17
`
`
`
`Il.S. Patent No. 5.659.891
`
`lc2
`
`x;q--,,
`
`B54
`c4
`
`Figuro 9: Simulatcd cylin&ical anay parcrns
`wirh dirlqcDt phasc disribu&ms,
`
`36. One ofordinary skill in the art would have been motivated to utilize a single
`
`cylindrical antenna structure to emit the output signals ofthe three co-located transmitters de-
`
`scribed by Petrovic in view of Raith instead of three separate antennas, because a single antenna
`
`structure "[c]an be used to realize advantages such as . . . hardware savings. low manufacturing
`
`costs, [and] low installation costs," as recognized by Alakija. Ex SAM10l5, p. 3.
`III. Conclusion
`37 .
`
`I hereby declare that all statements made herein of my own knowledge are true
`
`and that all statements made on information and beliefare believed to be true; and further that
`
`these statements were made with the knowledge that willful false statements and the like so
`
`made are punishable by fine or imprisonment. or both. under Section l00l of Title l8 of the
`
`United States Code.
`
`Date:
`
`Signature:
`
`los K. Kakaes, Ph.D.
`
`Page 18 of 23
`
`18
`
`
`
`
`
`APOSTOLOS K. KAKAES
`Cosmos Communications Consulting Corporation, President
`908 Park St. SE, Suite 201
`Vienna, Virginia 22180
`703-310-6076 (Office); 703-981-0999 (Mobile);
`e-mail: akakaes@gmail.com
`
`AREAS OF EXPERTISE
`
`All aspects of fixed and mobile communications. Over the years, my emphasis has been both in
`breadth and in depth, originally in fixed communications networks and then in mobile
`communications. Specific areas of in-depth expertise include:
` LTE/LTE-Advanced and evolution issues of 3G to 4G and beyond
` UMTS, including FDD, TDD, HSDPA/HSUPA, HSPA+, both air interface (UTRA) and
`core networking issues
` cdma2000 family from IS-95, through its evolution to 1x, 3x, 1xEV-DO (HDR), 1xED-
`DV (all aspects of the evolution to “3G” and beyond)
` Wireless Local Area Networks (LAN), Metropolitan Area Networks (MAN), and
`Personal Area Networks (PAN) technologies, Paging networks, Ad hoc networks,
`including IEEE 802.11 (WiFi), IEEE 802.16 (WiMAX), HIPERLAN, Bluetooth, Near
`Field Communications, IrDA (Infrared Data Association) operating with any of the
`available access technologies
` GSM, GPRS, EDGE (EGPRS) and related evolutionary issues
` North American TDMA and IS-136
` TETRA
`iDENTM
`
` Core Network technologies, IS-41, SS7, ATM, MAP, etc.
` Voice over IP (VoIP)
` Design and implementation of voice and data networking (circuit switching as well as all
`the evolving all IP-based technologies)
` Traffic engineering and network design; both air interface aspects (including resource
`allocation, QoS, MAC protocol, etc.) and design of core network, both user plane and
`control plane
`
`EMPLOYMENT HISTORY
`
`9/88 – Present
`Cosmos Communications Consulting Corporation. Founder and president of private
`communications engineering consulting firm specializing in mobile communications. Initially
`part time; full time since 1994.
` Developed and presented courses, seminars, and lectures on fixed and mobile
`communications to both corporate and government entities, such as the FCC and the US
`Marshal’s Office.
` Consulted on high level technology-related issues and trends, pros and cons of each, etc.
`to corporate entities, governmental agencies, and international organizations, such as the
`UN.
`
`Page 19 of 23
`
`
`19
`
`
`
`
`
` Consulted at the detailed technical level to engineering firms, operators, and equipment
`vendors on technical issues related to existing or evolving technologies for mobile
`communications.
` Served as technology consultant to the investment community both fixed and wireless
`communications technologies.
` Served as consultant and expert witness on both civil and criminal legal cases, including
`a class action lawsuit brought in California, a murder case in Illinois, and several patent
`infringement cases both at the ITC and in district court.
` Participated as a technical consultant in the analysis of large patent portfolios for the
`purposes of due diligence, sales, and/or M/A activities for some of the largest companies
`in the mobile communications space.
`
`These projects spanned a multidimensional spectrum of
` Technologies: both fixed and mobile communications as they have evolved over the past
`30+ years;
` Audiences: non-technical support personnel, highly specialized engineers, Wall Street
`analysts, hedge fund managers, litigation teams, as well as decision making executives at
`the CEO/CFO/CTO level;
` Geographic and cultural backgrounds that span all continents and over 40 countries.
`
`9/87 - 5/94
`The George Washington University, Washington, D.C. Department of Electrical Engineering and
`Computer Science.
` Taught mostly graduate courses in the area of communication engineering, including
`communication theory, coding theory, voice and data networking, and mobile
`communications.
` Proposed, developed and taught new graduate courses in the area of mobile
`communications.
` Received several research awards/grants, including the prestigious NSF Research
`Initiation Award.
` Participated in several committees, including the departmental Graduate Curriculum
`Committee as well as various University-wide committees.
`
`7/85 - 12/86
`Polytechnic Institute of New York, Brooklyn, New York. Joint appointment as Special Research
`Fellow and Adjunct Instructor (while pursuing the Ph.D. degree)
`
`1/82 - 7/87
`AT&T Bell Laboratories, Holmdel, New Jersey. Worked on modeling, analysis, design, and
`performance evaluation of voice and data networks. Developed algorithms for DNHR
`(Dynamic, Non-Hierarchical Routing) used in the telephone network. Analysis of advanced data
`services and formulation of long term plans for development of enhanced data services and
`network design tools to support such services.
`
`7/76 - 12/81
`University of Colorado, Boulder, Colorado and Michigan State University, East Lansing,
`Michigan. Undergraduate and then graduate teaching assistant.
`
`Page 20 of 23
`
`
`20
`
`
`
`
`
`EDUCATION
`
`09/82 - 01/88
`Polytechnic Institute of New York. Ph.D. in Electrical Engineering.
`Thesis Title: Topological Properties and Design of Multihop Packet Radio Networks.
`Thesis Advisor: Professor Robert R. Boorstyn.
`
`09/74 - 06/80
`University of Colorado.
`in Electrical Engineering.
`a minor
`M.S.
`in Applied Mathematics with
`B.S. in Applied Mathematics with a minor in Electrical Engineering.
`
`PROFESSIONAL ASSOCIATIONS AND ACTIVITIES
`
` Member of the IEEE (Active in the Communications Society and the Information Theory
`Society).
` Secretary, IEEE Commun