`EXHIBIT 2084
`
`
`
`
`
`From:
`Sent:
`To:
`Subject:
`
`Attachments:
`
`Ying-Moh Liu <yml7245@yahoo.com>
`Monday, June 29, 2015 11:07 PM
`McCormack, Brian C
`Fw: Revised ~ RFQ EML 06-1010 (Drawing Number 105-1012 Rev 2 with
`exceptions/modifications)
`106-1012.pdf
`
`
`----- Forwarded Message -----
`From: Mahir Abrahim <MAbrahim@creativedis.com>
`To: Ying-Moh Liu <yml7245@yahoo.com>
`Cc: Jerry Carollo <JCarollo@creativedis.com>
`Sent: Tuesday, October 17, 2006 8:13 AM
`Subject: RE: Revised ~ RFQ EML 06-1010 (Drawing Number 105-1012 Rev 2 with exceptions/modifications)
`
`Here’s the updated dwg. Let me know if I missed anything.
`
`
`
`From: Ying-Moh Liu [mailto:yml7245@yahoo.com]
`Sent: Monday, October 16, 2006 9:39 AM
`To: Mahir Abrahim
`Cc: Jerry Carollo
`Subject: Fwd: Revised ~ RFQ EML 06-1010 (Drawing Number 105-1012 Rev 2 with exceptions/modifications)
`
`
`Mahir:
`
`
`Would you revise the mirror drawing according to vendor's inputs and make sure that they are still
`acceptable? I believe they are acceptable optically. Please let me know if you see any issues. Thank you.
`
`
`Ying-Moh
`
`Note: forwarded message attached.
`
`
`
`Get your email and more, right on the new Yahoo.com
`
`
`1
`
`REALD INC.
`Exhibit 2084-1
`MASTERIMAGE 3D, et al. v REALD INC.
`IPR2015-00035
`
`
`
`REV
`
`A
`
`DRAWING NUMBER
`
`Carlsbad, CA 92010
`5909 Sea Lion Place
`(760) 476-0339
`Suite A
`
`SHEET 1 OF 1
`106-1012
`MIRROR, 12" DIA, D-CUT
`
`0.250
`
`SIZE
`
`B
`
`CODE IDENT NO.
`
`66689
`
`SCALE:
`
`M. ABRAHIM14-Sep-06
`mabrahim13-Sep-06
`
`
`
`FILE/PART NO. 106-1012-001
`
`APVD
`APVD
`APVD
`PROD MGR
`QA
`MFG
`CHECK
`DRAFT
`DESIGN
`
`FINISH: SEE NOTE
`
`MATERIAL: PYREX, FINE ANNEALED
`
` EDGES AND CORNERS MAX: R .010 OR
`REMOVE ALL BURRS. BREAK ALL SHARP
`.XX 0.010 .XXX .005 ANGLES 0.5
` DIMENSIONS ARE IN INCHES, TOLERANCES:
`INTERPRET PER ASME Y14.5M-1994
`
`.010 X .010 CHAMFER MAX.
`
`F2
`
`F1
`
`x45 TYP
`
`-.005
`.020+.015
`
`.500
`
`12.00
`
`4.50
`
`PRO/E REL LEVELPROI_RELEASE
`PRO/E VERSION
`PROI_VERSION
`
`APPD
`
`
`
`DATE
`
`
`
`1024
`
`PRODUCTION RELEASE
`
`DESCRIPTION
`
`EO
`REVISIONS
`
`LTR
`
`A
`
`6. SURFACE QUALITY: 80-50 SCRATCH-DIG
` F2 = MACHINE GROUND AND POLISHED
`5. SURFACE FIGURE: F1 = < 1/2 WAVE AT 633NM (BEST EFFORT)
`4. COATING: F1 = ENHANCED AL WITH REFLECTIVITY >95% OVER 400-700NM
`3. CLEAR APERTURE: 2.5MM FROM EDGE OF OD (BEST EFFORT)
` THIS DRAWING SHALL BE LOCATED
`.010ABC
`2. FEATURES WHICH ARE NOT OTHERWISE DIMENSIONED ON
` REVISION ON THIS DRAWING (I.E. XXX-XXXX-XXX_REV)
` PART FILE NAME MUST HAVE PART NUMBER FOLLOWED BY
` 106-1012-001_A
`1. FABRICATE PARTS USING ELECTRONIC DATA BASE FILE
`NOTES: UNLESS OTHERWISE SPECIFIED
`
`
`
`
`
`
`
`
`
`
`
`
`
`
`
`
`
`REALD INC.
`Exhibit 2084-2
`MASTERIMAGE 3D, et al. v REALD INC.
`IPR2015-00035
Accessing this document will incur an additional charge of $.
After purchase, you can access this document again without charge.
Accept $ Charge
Still Working On It
This document is taking longer than usual to download. This can happen if we need to contact the court directly to obtain the document and their servers are running slowly.
Give it another minute or two to complete, and then try the refresh button.
A few More Minutes ... Still Working
It can take up to 5 minutes for us to download a document if the court servers are running slowly.
Thank you for your continued patience.
This document could not be displayed.
We could not find this document within its docket. Please go back to the docket page and check the link. If that does not work, go back to the docket and refresh it to pull the newest information.
Your account does not support viewing this document.
You need a Paid Account to view this document. Click here to change your account type.
Your account does not support viewing this document.
Set your membership
status to view this document.
With a Docket Alarm membership, you'll
get a whole lot more, including:
- Up-to-date information for this case.
- Email alerts whenever there is an update.
- Full text search for other cases.
- Get email alerts whenever a new case matches your search.
One Moment Please
The filing “” is large (MB) and is being downloaded.
Please refresh this page in a few minutes to see if the filing has been downloaded. The filing will also be emailed to you when the download completes.
Your document is on its way!
If you do not receive the document in five minutes, contact support at support@docketalarm.com.
Sealed Document
We are unable to display this document, it may be under a court ordered seal.
If you have proper credentials to access the file, you may proceed directly to the court's system using your government issued username and password.
Access Government Site
